Emerson RTM-ATCA-F120-OPT manual Standard Compliances, Standard Description

Page 23

Introduction

1.2Standard Compliances

This RTM-ATCA-F120-OPT meets the following standards.

Table 1-1 Standard Compliances

Standard

Description

 

 

UL 60950-1

Legal safety requirements

EN 60950-1

 

IEC 60950-1

 

CAN/CSA C22.2 No 60950-1

 

 

 

CISPR 22

EMC requirements (legal) on system level (predefined

CISPR 24

Emerson system)

 

EN 55022

 

EN 55024

 

FCC Part 15

 

Industry Canada ICES-003

 

VCCI Japan

 

AS/NZS CISPR 22

 

EN 300 386

 

NEBS Standard GR-1089 CORE

 

 

 

NEBS Standard GR-63-CORE

Environmental requirements

ETSI EN 300019 series

 

 

 

PICMG 3.0 R2.0

Defines mechanics, blade dimensions, power

 

distribution, power and data connectors, and system

 

management

 

 

The product has been designed to meet the directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) Directive 2011/65/EU.

For Declaration of Conformity refer, RTM Declaration of Conformity..

RTM-ATCA-F120-OPT Installation and Use (6806800G29C)

23

Image 23
Contents RTM-ATCA-F120-OPT Contact Address Contents Contents List of Tables RTM-ATCA-F120-OPT Installation and Use 6806800G29CList of Tables List of Figures List of Figures Abbreviations Overview of ContentsAbout this Manual Bold ConventionsAbout this Manual Notation DescriptionPart Number Publication Date Description Summary of ChangesAbout this Manual Electrical Interference Safety NotesOperation InstallationSafety Notes SFP/SFP+ Modules Environment Sicherheitshinweise Sicherheitshinweise EMVBeschädigung von Schaltkreisen Verletzungsgefahr UmweltschutzIntroduction FeaturesIntroduction Standard Description Standard CompliancesOrdering Information Feature ValueMechanical Data Unpacking and Inspecting the RTM Hardware Preparation and InstallationOverview Environmental Requirements Environmental and Power RequirementsHardware Preparation and Installation Requirement Operating Non-Operating Power RequirementsInstalling the RTM Installing and Removing the RTMHardware Preparation and Installation Hardware Preparation and Installation Installation Procedure without Installed Front Blade Close the handles of the front blade Removing the RTM Removal ProcedureHardware Preparation and Installation Installing and Removing SFP/ SFP+ Modules Hardware Preparation and Installation Procedure Installing an SFP/SFP+ ModuleConnect the network cable to the SFP/SFP+ module Remove any connected cable from the SFP module Removing an SFP/SFP+ ModuleHardware Preparation and Installation Controls, LEDs and Connectors Controls, LEDs and Connectors LEDs and Interface ConnectorsDuring RTM removal Interface ConnectorsDuring RTM installation LEDsFabric Channel Uplinks Location of Ethernet Fabric Channel Uplink Interfaces Ethernet Type Face Plate Label2.1.2 1 GBit Fabric Interface Uplinks Base Channel Interface ConnectorsLocation of Base Interface Uplink Interface Connectors 2.2.1 10 GBit Base Interface Uplinks 2.3 SFP/SFP+ Module Hot Swap Location of Clock Extension Connectors Controls, LEDs and Connectors Telecom Clocking ConnectorsSerial Interface Connector Location of Serial Interface Connectors Pin Signal Functional Description Functional Description Block DiagramSensor Name Sensor Type Sensor Number Mezzanine Management ControllerRTM-F120-OPT MMC Functional Description Location of Ipmi Temperature Sensors Functional Description RTM-ATCA-F120-OPT Installation and Use 6806800G29C Document Title and Source Publication Number Emerson Network Power Embedded Computing DocumentsARelated Documentation Related Documentation Index Index Page Embedded Computing HOW to Reach Literature and Technical Support