Emerson RTM-ATCA-F120-OPT manual Base Channel Interface Connectors

Page 47

Controls, LEDs and Connectors

3.2.2.1.21 GBit Fabric Interface Uplinks

The two cages for 1 GBit connections can be equipped with standard SFP connectors for copper and optical connections.

The SFP modules can be installed/removed both while the RTM is powered and non-powered. The presence and also the type of SFP modules is automatically detected.

When using copper SFP modules, the speed is determined through auto-negotiation per the 802.11 Ethernet specification. Optical modules do not support auto-negotiation.

The following table shows which switch MIB OID each cage corresponds to.

Table 3-3 Fabric Channel 1 GBit Uplink Connectors - Port - MIB OID Assignment

Face Plate Label	MIB OID	Ethernet Type

FIX GE1	<shelf>.<slot>.2.40	1 GBit

FIX GE2	<shelf>.<slot>.2.41	1 GBit

3.2.2.2Base Channel Interface Connectors

The RTM provides access to the folllowing six Ethernet base channel uplink interfaces at its face plate:

zTwo 10 Gigabit Ethernet uplink interfaces via SFP+ connectors

zFour 1 Gigabit Ethernet interfaces via SFP connectors

RTM-ATCA-F120-OPT Installation and Use (6806800G29C)

47

Image 47

Contents RTM-ATCA-F120-OPT Contact Address Contents Contents List of Tables RTM-ATCA-F120-OPT Installation and Use 6806800G29CList of Tables List of Figures List of Figures Abbreviations Overview of ContentsAbout this Manual Bold ConventionsAbout this Manual Notation DescriptionPart Number Publication Date Description Summary of ChangesAbout this Manual Electrical Interference Safety NotesOperation InstallationSafety Notes SFP/SFP+ Modules Environment Sicherheitshinweise Sicherheitshinweise EMVBeschädigung von Schaltkreisen Verletzungsgefahr UmweltschutzIntroduction FeaturesIntroduction Standard Description Standard CompliancesOrdering Information Feature ValueMechanical Data Unpacking and Inspecting the RTM Hardware Preparation and InstallationOverview Environmental Requirements Environmental and Power RequirementsHardware Preparation and Installation Requirement Operating Non-Operating Power RequirementsInstalling the RTM Installing and Removing the RTMHardware Preparation and Installation Hardware Preparation and Installation Installation Procedure without Installed Front Blade Close the handles of the front blade Removing the RTM Removal ProcedureHardware Preparation and Installation Installing and Removing SFP/ SFP+ Modules Hardware Preparation and Installation Procedure Installing an SFP/SFP+ ModuleConnect the network cable to the SFP/SFP+ module Remove any connected cable from the SFP module Removing an SFP/SFP+ ModuleHardware Preparation and Installation Controls, LEDs and Connectors Controls, LEDs and Connectors LEDs and Interface ConnectorsDuring RTM removal Interface ConnectorsDuring RTM installation LEDsFabric Channel Uplinks Location of Ethernet Fabric Channel Uplink Interfaces Ethernet Type Face Plate Label2.1.2 1 GBit Fabric Interface Uplinks Base Channel Interface ConnectorsLocation of Base Interface Uplink Interface Connectors 2.2.1 10 GBit Base Interface Uplinks 2.3 SFP/SFP+ Module Hot Swap Location of Clock Extension Connectors Controls, LEDs and Connectors Telecom Clocking ConnectorsSerial Interface Connector Location of Serial Interface Connectors Pin Signal Functional Description Functional Description Block DiagramSensor Name Sensor Type Sensor Number Mezzanine Management ControllerRTM-F120-OPT MMC Functional Description Location of Ipmi Temperature Sensors Functional Description RTM-ATCA-F120-OPT Installation and Use 6806800G29C Document Title and Source Publication Number Emerson Network Power Embedded Computing DocumentsARelated Documentation Related Documentation Index Index Page Embedded Computing HOW to Reach Literature and Technical Support