Emerson RTM-ATCA-F120-OPT manual Functional Description

Page 59

Functional Description

Table 4-1 IPMI Sensors Overview (continued)

Sensor Name

Sensor Type

Sensor Number

 

 

 

TX Fault SFP01

Other FRU

0x30

 

 

 

TX Fault SFP02

Other FRU

0x31

 

 

 

TX Fault SFP03

Other FRU

0x32

 

 

 

TX Fault SFP04

Other FRU

0x33

 

 

 

TX Fault SFP05

Other FRU

0x34

 

 

 

TX Fault SFP06

Other FRU

0x35

 

 

 

TX Fault SFP07

Other FRU

0x36

 

 

 

TX Fault SFP08

Other FRU

0x37

 

 

 

TX Fault SFP09

Other FRU

0x38

 

 

 

TX Fault SFP10

Other FRU

0x39

 

 

 

TX Fault SFP11

Other FRU

0x3A

 

 

 

TX Fault SFP12

Other FRU

0x3B

 

 

 

The following figure shows the location of the on-board temperature sensors.

RTM-ATCA-F120-OPT Installation and Use (6806800G29C)

59

Image 59
Contents RTM-ATCA-F120-OPT Contact Address Contents Contents List of Tables RTM-ATCA-F120-OPT Installation and Use 6806800G29CList of Tables List of Figures List of Figures Abbreviations Overview of ContentsAbout this Manual Bold ConventionsAbout this Manual Notation DescriptionPart Number Publication Date Description Summary of ChangesAbout this Manual Electrical Interference Safety NotesOperation InstallationSafety Notes SFP/SFP+ Modules Environment Sicherheitshinweise Sicherheitshinweise EMVBeschädigung von Schaltkreisen Verletzungsgefahr UmweltschutzIntroduction FeaturesIntroduction Standard Description Standard CompliancesOrdering Information Feature ValueMechanical Data Unpacking and Inspecting the RTM Hardware Preparation and InstallationOverview Environmental Requirements Environmental and Power RequirementsHardware Preparation and Installation Requirement Operating Non-Operating Power RequirementsInstalling the RTM Installing and Removing the RTMHardware Preparation and Installation Hardware Preparation and Installation Installation Procedure without Installed Front Blade Close the handles of the front blade Removing the RTM Removal ProcedureHardware Preparation and Installation Installing and Removing SFP/ SFP+ Modules Hardware Preparation and Installation Procedure Installing an SFP/SFP+ ModuleConnect the network cable to the SFP/SFP+ module Remove any connected cable from the SFP module Removing an SFP/SFP+ ModuleHardware Preparation and Installation Controls, LEDs and Connectors Controls, LEDs and Connectors LEDs and Interface ConnectorsDuring RTM removal Interface ConnectorsDuring RTM installation LEDsFabric Channel Uplinks Location of Ethernet Fabric Channel Uplink Interfaces Ethernet Type Face Plate Label2.1.2 1 GBit Fabric Interface Uplinks Base Channel Interface ConnectorsLocation of Base Interface Uplink Interface Connectors 2.2.1 10 GBit Base Interface Uplinks 2.3 SFP/SFP+ Module Hot Swap Location of Clock Extension Connectors Controls, LEDs and Connectors Telecom Clocking ConnectorsSerial Interface Connector Location of Serial Interface Connectors Pin Signal Functional Description Functional Description Block DiagramSensor Name Sensor Type Sensor Number Mezzanine Management ControllerRTM-F120-OPT MMC Functional Description Location of Ipmi Temperature Sensors Functional Description RTM-ATCA-F120-OPT Installation and Use 6806800G29C Document Title and Source Publication Number Emerson Network Power Embedded Computing DocumentsARelated Documentation Related Documentation Index Index Page Embedded Computing HOW to Reach Literature and Technical Support