Samsung SW-224 manual Your CD-R/RW Drive, Upgrading the Firmware Flash Memory, System Requirements

Page 5

SW-224_eng-02 12/19/01 4:42 PM Page 4

Your CD-R/RW Drive

 

5

 

6

1

2

3

4

1.Connector for stereo headphones with a 3.6 mm stereo mini-jack

2.Headphone volume control

3.Emergency eject hole (if the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmly)

4.Indicator light (when it is green, a disc is being read or recorded)

5.Disc compartment (the compartment opens and closes automatically when you press the Eject button)

6.Eject button

1

2

3

4

5

1.Two-pin digital audio output terminal for use with a sound or MPEG card supporting digital audio features

2.Four-pin sound output terminal for use with a sound card (refer to the sound card documentation for further details)

3.Master/slave select terminal

4.40pin host E-IDE interface connector

5.4pin power terminal

Upgrading the Firmware Flash Memory

The product firmware can be upgraded by downloading the updated file from the following Web site:

http://www.samsungodd.com

www.samsungelectronics.com

System Requirements

Before you install the CD-R/RW drive, we strongly recommend that you check that your setup meets the system requirements listed below.

Item

Description

Computer

Intel Pentium II (or higher), 32 MB of RAM (or higher)

 

with an E-IDE interface

 

 

Disk space

700 MB minimum

 

 

Windows version

Windows 95 / 98 OSR2 / 2000 / ME or XP /

 

Windows NT 4.0 (or higher)

 

 

General DMA Installation Guide

Windows 95/98/Me

Important!

Please read the entire DMA installation guide before installing your CD-R/RW drive.

About DMA Installation

For stable writing performance at high speeds, Installation of DMA transfer mode for E-IDE/ATAPI interface is strongly recommended.

We recommend DMA mode for fast writing.

DMA Setting

Before you install your CD-R/RW drive, we recommend to set DMA to enabled on your PC system. See the following procedure to set DMA transfer mode in windows oprerating system. (Windows 95 OSR2/98/ME)

Click on START

Select your CD-R/RW drive

Click on Settings

Click on the Properties button

Select Control Panel

Click on the Settings tab

Select the System Icon

Check the DMA checkbox to enables DMA.

Select the Device Manager panel Click OK

in System Properties

Restart your PC

Expand the CD-ROM icon

Windows 2000/XP

Select the DMA mode by selecting [Start > Setting > Control Panel > System > Device Manager > IDEATA/ATAPI Controller > Default/Assistant IDE Channel Advanced Information]

4

5

Image 5
Contents Page SW-224 Users Guide Contents Safety PrecautionsDMA Setting About DMA InstallationYour CD-R/RW Drive Upgrading the Firmware Flash MemoryConnecting the E-IDE cable Two configurations are possible Installing the CD-R/RW DriveConnecting the Cables Add the DEVICE=C\SAMSUNG\SSCDROM.SYS \DSSCD000 /V entry Setting Up the Device DriverEdit the AUTOEXEC.BAT file Add the C\SAMSUNG\MSCDEX /DSSCD000 entryStoring and Cleaning Your Discs Using the CD-R/RW DrivePush the power button and boot the computer Playing Audio CDsPlease refer to help menu of writing software provided Recommended Disc TypesWhat is Auto-Run? What is Buffer Under-Run?What is Super-Link? How to cancel select the Auto-Run functionMeaning / Solution Solving Technical ProblemsTechnical Specifications Manual del usuario Índice general Precauciones de seguridadRequisitos del sistema Su unidad de CD grabable/regrabableActualización de la memoria flash del firmware Conexión del cable E-IDE Instalación de la unidadConexión de los cables Agregue la entrada C\SAMSUNG\MSCDEX /DSSCD000 Configuración del controlador del dispositivoEdite el archivo AUTOEXEC.BAT Almacenamiento y limpieza de los discos Uso de la unidad de CD grabable/regrabablePresione el botón de alimentación y arranque el ordenador El indicador luminoso se enciende Reproduzca el disco CDTipos de discos recomendados Descripción de los Términos Precaución con los erroresQué es Buffer Under-Run? Qué es Auto-Run?De CD-R/RW Solución de problemas técnicosCD-R/RW después Significado / SoluciónEspecificaciones técnicas Bedienungsanleitung Deutsch Notöffnung LautstärkereglerLED-Anzeige Lesen/Schreiben CD-ROM-SchubladeBetrifft Beschreibung Über die DMA InstallationWichtig DMA EinstellungGebrauch von einem Kabelanschluß1E-IDE Kabel Benutzen von zweiWiedergabe von Audio CDs Empfohlene Discs Probleme während der AufzeichnungErklärung der Begriffe Hinweise bei FehlermeldungenWas bedeutet Buffer Under-Run? Was bedeutet Auto-Run?Problem Ursache/Abhilfe Falls Probleme auftretenSamsung CD-R/RW SW Arbeitsplatz System steverung Geräte ManagerRecorder Samsung CD-R/RW SW XP oder NT4.0Le Guide De L’utilisateur-FRANÇAIS Dispositif de configuration pontet Bouton contrôle volumePrise Casque Le trou déjection durgenceMode de Upgrade de Flash Memory Pumware Mode dinstallation du lecteur CD-R/RWInstallation du DMA Conditions requises du systèmeConnexion au câble du secteur Mode de connexion au câbleConnexion du câble de démarrage au sélecteur Maître/Esclave Connexion au câble E-IDEMise en marche de CDs audio Autres En cas de problèmes durant lenregistrement’avertissement sur la production des erreurs ’explication des termesBuffer Underrun AutorunMise en vérification Problème Signification/SolutionMon Ordinateur Contrôle Systéme Manager Spécifications techniquesEnregistrement Samsung CD-R/RW SW Vérifiez l’unité CD-R/RWWindows 95/98/2000/ME/XP ou NT