Mitsubishi Electronics PD-5010 manual Rear View/ Terminal Board

Page 10

Rear View/ Terminal Board

AEXT SPEAKER L and R

Connect speakers here. Maintain the correct polarity.

BVIDEO 1, 2, 3

Connect a VCR or other video device here. Only one of these three inputs can be used.

CDVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc. here.

DRGB1

Inputs the analog RGB signal of personal computer, etc.

ERGB2/ DVD2/ HD2

RGB2:

Inputs the analog RGB signal.

DVD2/ HD2: Connect DVD’s, High Definition or Laser Discs, etc. here.

FMONITORLINKTM (M-LINK) INPUT

A proprietary input for connecting a Mitsubishi tuner/ controller. Input will appear in menus only after the proprietary tuner/controller has been connected.

GCONTROL LOCK

When “CONTROL LOCK” is set “ON”, the buttons on the set’s control panel do not function.

HREMOTE CONTROL

Connect the supplied remote cable here.

IMONITORLINKTM CONTROL

This terminal can be used for external control of power ON/OFF, input selection AUDIO MUTE and other features. It is also used with a proprietary Mitsubishi tuner/controller.

JAUDIO1 / AUDIO2 / AUDIO3

Audio 1: Connect the audio output from the device connected to Video 1, 2 or 3.

Audio 2: Connect the audio output from the device connected to DVD1/HD1.

Audio 3: Connect the audio output from the device connected to RGB2/DVD2/HD2.

KAC IN

Connect the included power cord here.

4

Image 10
Contents Owner’s Guide Page Precautions Important InformationTo avoid damage and prolong operating life Contents Page Attachment Options for the PD-5010 Monitor Introduction Part Names and Function Rear View/ Terminal Board Remote Control Battery Installation and Replacement Using the wired remote control mode Installation Connecting Your PC or Macintosh Computer External Speaker Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Basic Operations InformationAfter the power is turned off with the off timer To set the off timerTo cancel the off timer To check the remaining timeWide Operations Watching with a wide screen manualPicture Size setting When Picture Size is set to OFFInformation Supported resolution Watching computer imagesShowing a couple of pictures on the screen at the same time Operations in the Side-by-side modePIP Screen Operations InformationSelecting the input signals to be displayed Operations in the Picture-in-picture modeAdjusting the ON-SCREEN Menu controls On Screen Menu Controls Menu OperationsMain menu Sub menu Functions Default Information Video Settings screen Picture Settings MenuAdjusting the picture Adjusting the computer imageExample Setting the Theater mode Information Types of picture modesOnce the setting is completed Setting the color temperatureExample Setting LOW Information Setting the color temperatureExample Adjusting the White Balance Adjusting the color to the desired qualityInformation Adjusting the white balance Reducing noise in the picture Example Setting NR-3Types of noise reduction Example Adjusting the bass Audio Settings MenuAdjusting the treble, bass and left/right balance Information Sound settings menuExample Adjusting the vertical position in the normal mode Monitor Settings MenuInformation When Auto Picture is OFF Example Turning the on-screen menu mode off Setting the on-screen menuFunction Menu To adjust the position Adjusting the position of the menu displayExample Adjusting the position of the menu display Information Adjusting the position of the menu displayInformation Power management function Setting the power management for computer imagesExampleTurning the power management function on Power management settingsPOWER/STANDBY indicator Example Adjusting the Gray Level Setting the gray level for the sides of the screenSetting the picture to suit the movie Example Setting the Cinema Mode to OFFInformation When you adjust the M-LINK ADJ Setting Monitorlink M-LINK ADJExample Setting Example Setting PLE to LockSetting the time for Inverse Peak Luminance Enhancement PLEInformation Setting the time Setting the time for Screen WiperTo select on for the Working Time Resetting to the default values SpeedSetting the BNC connectors Options Setting MenuSetting the allocation of the audio connectors Example Setting Audio 1 to VideoTo set the RGB select mode to Motion Setting a computer image to the correct RGB select screenExample Setting the RGB Select mode to Motion See page 55 for the details of the above settingsSetting the picture size for RGB input signals Setting high definition images to the suitable screen sizeInformation HD Select modes Information Language settings Setting the language for the menusExample Setting the menu display to Deutsch Information MenuInformation Video signal formats Setting the video signal formatExample Setting the video signal format to 3.58 Ntsc To select 3.58 NtscConnections External ControlApplication Communication FormatPower OFF Command Reference ListPower on Input Switch ChangeAudio Mute Off Volume Gain DataAudio Mute On Contrast Gain DataColor Gain Data Picture Mode SelectRED Gain Data Blue Gain Data NR Mode SetGreen Gain Data Bass Gain Data22. V. Position Gain Data Screen Mode SelectBalance Gain Data 23. H. Position Gain DataClock Gain Data Phase Gain DataAuto Picture Select Menu SelectMenu ADJ. Gain Data Power MGT SelectCinema Mode Set Gray Level SetScreen Wiper Set Inverse SetAudio Select Set Picture Size Select RGB SelectHD Select Language SelectColor System Select Multi Screen SelectFrequency Request Input Mode RequestHorizontal sync polarity Video ADJ Request Audio Select Request Failure Mode RequestModel Name Request Supported resolution Table of Signals SupportedComputer input signals supported by this system Page Troubleshooting Symptom Checks RemedySpecifications SignalsPage Mitsubishi Plasma Display Panel Limited Warranty