Mitsubishi Electronics manual Attachment Options for the PD-5010 Monitor

Page 7

Attachment Options for the PD-5010 Monitor

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

*While it is upright. (See Drawing A)

*As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

•This device cannot be installed on its own. Be sure to use a stand or wall mount kit.

* See page 2.

•For correct installation and mounting it is strongly recommended to use a trained, authorized Mitsubishi dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.

Product warranty does not cover damage caused by improper installation.

*Use only a matching stand or wall mount kit designed to fit this product.

Ventilation Requirements for enclosure mounting

To allow heat to disperse, leave space between surrounding objects as shown on the diagram at the right, when installing.

1

Image 7

Contents Owner’s Guide Page Important Information PrecautionsTo avoid damage and prolong operating life Contents Page Attachment Options for the PD-5010 Monitor Introduction Part Names and Function Rear View/ Terminal Board Remote Control Battery Installation and Replacement Using the wired remote control mode Installation Connecting Your PC or Macintosh Computer External Speaker Connections Pin Assignments and Signal Levels for 15 pin RGB Analog Information Basic OperationsTo check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timerWatching with a wide screen manual Wide OperationsWatching computer images When Picture Size is set to OFFInformation Supported resolution Picture Size settingInformation Operations in the Side-by-side modePIP Screen Operations Showing a couple of pictures on the screen at the same timeSelecting the input signals to be displayed Operations in the Picture-in-picture modeAdjusting the ON-SCREEN Menu controls Menu Operations On Screen Menu ControlsMain menu Sub menu Functions Default Adjusting the computer image Picture Settings MenuAdjusting the picture Information Video Settings screenInformation Types of picture modes Example Setting the Theater modeInformation Setting the color temperature Setting the color temperatureExample Setting LOW Once the setting is completedExample Adjusting the White Balance Adjusting the color to the desired qualityInformation Adjusting the white balance Reducing noise in the picture Example Setting NR-3Types of noise reduction Information Sound settings menu Audio Settings MenuAdjusting the treble, bass and left/right balance Example Adjusting the bassExample Adjusting the vertical position in the normal mode Monitor Settings MenuInformation When Auto Picture is OFF Example Turning the on-screen menu mode off Setting the on-screen menuFunction Menu Information Adjusting the position of the menu display Adjusting the position of the menu displayExample Adjusting the position of the menu display To adjust the positionPower management settings Setting the power management for computer imagesExampleTurning the power management function on Information Power management functionPOWER/STANDBY indicator Example Setting the Cinema Mode to OFF Setting the gray level for the sides of the screenSetting the picture to suit the movie Example Adjusting the Gray LevelExample Setting PLE to Lock Setting Monitorlink M-LINK ADJExample Setting Information When you adjust the M-LINK ADJPeak Luminance Enhancement PLE Setting the time for InverseInformation Setting the time Setting the time for Screen WiperTo select on for the Working Time Speed Resetting to the default valuesExample Setting Audio 1 to Video Options Setting MenuSetting the allocation of the audio connectors Setting the BNC connectorsSee page 55 for the details of the above settings Setting a computer image to the correct RGB select screenExample Setting the RGB Select mode to Motion To set the RGB select mode to MotionSetting the picture size for RGB input signals Setting high definition images to the suitable screen sizeInformation HD Select modes Information Menu Setting the language for the menusExample Setting the menu display to Deutsch Information Language settingsTo select 3.58 Ntsc Setting the video signal formatExample Setting the video signal format to 3.58 Ntsc Information Video signal formatsCommunication Format External ControlApplication ConnectionsInput Switch Change Command Reference ListPower on Power OFFContrast Gain Data Volume Gain DataAudio Mute On Audio Mute OffColor Gain Data Picture Mode SelectRED Gain Data Bass Gain Data NR Mode SetGreen Gain Data Blue Gain Data23. H. Position Gain Data Screen Mode SelectBalance Gain Data 22. V. Position Gain DataMenu Select Phase Gain DataAuto Picture Select Clock Gain DataGray Level Set Power MGT SelectCinema Mode Set Menu ADJ. Gain DataScreen Wiper Set Inverse SetAudio Select Set Language Select RGB SelectHD Select Picture Size SelectMulti Screen Select Color System SelectFrequency Request Input Mode RequestHorizontal sync polarity Video ADJ Request Audio Select Request Failure Mode RequestModel Name Request Supported resolution Table of Signals SupportedComputer input signals supported by this system Page Symptom Checks Remedy TroubleshootingSignals SpecificationsPage Mitsubishi Plasma Display Panel Limited Warranty