Mitsubishi Electronics DX-TL2500U operation manual Archive/Full Rec/Rem, ARCHIVE/SIZE/ Data Error

Warnings and CALL OUT output

■Warnings and their appropriate countermeasures

#1 Options in the CALL OUT options column:

• Selectable	: CALL OUT output can be selected/de-selected on the menu.
• Fixed	:	a CALL OUT signal is emitted without prior selection of this function using the menu.
• None	:	no CALL OUT signal is emitted, but a warning indicator will appear on screen.

CALL OUT signal output can be stopped by pressing the WARNING RESET button.

Warning Display	Status
REC/FULL	• MAIN HDD recordable
	capacity is full.
REC/SUB FULL	• SUB HDD recordable
	capacity is full.
COPY/FULL	• Media recordable
REST/FULL	capacity is full.
ARCHIVE/FULL
REC/REM	• The remaining HDD capa
	-city has reached the value
	set in HDD REMAIN.

Countermeasure	Canceling	Code	CALL OUT	page
			output
	the warning
			#1
• When the warning is	Press the	WNG1100	Selectable	53
cancelled, the unit will start	WARNING
over-writing the oldest data	RESET button.
remaining in the hard disk
drive.
• Copy data as necessary.		WNG1101		-
• Replace with new media.	Press the	WNG3100	None	-
• Replace media if necess	WARNING	WNG4100
-ary.	RESET button.	WNG7100	Selectable
• Copy data as necessary.	Press the	WNG1200	Selectable	58
	WARNING	(MAIN)
	RESET button. WNG1201
		(SUB)

ARCHIVE/REM

COPY/SIZE/

DATA ERROR REST/SIZE/

DATA ERROR

ARCHIVE/SIZE/ DATA ERROR

COPY/

MEDIA ERROR REST/

MEDIA ERROR ARCHIVE/

MEDIA ERROR

COPY/NO MEDIA REST/NO MEDIA ARCHIVE/

NO MEDIA

NO SIGNAL

(The warning will indicate the number of the non-functioning camera. )

•The data that is being copied/restored exceeds the capacity of the recor -ding device, or there is no original data.

•Error has occurred in the media as recording device.

•No inserted media.

•Video signal was lost for more than 5 seconds during recording.

		WNG7200
• Set the copy/restore	Press the	WNG3701	None	80, 81
range again.	WARNING	WNG4701
• Replace with new media.	RESET button.	WNG7701
• Check media in recording	Press the	WNG3702	None	16, 20
device. (Insert the media	WARNING	WNG4702		80, 81
if there is none.)	RESET button. WNG7702
• Check whether it is write-				-
protected by media.
It will cancel, if protected.
• After peripheral recording				-
device and the unit power
off a power supply, reboot in
order of peripheral recording
device and the unit.
• After peripheral recording				20
device and the unit power
off a power supply, please
perform the check of a
SCSI cable and termination.
• Insert the media.	Press the	WNG3703	None	-
	WARNING	WNG4703
	RESET button. WNG7703
• Check whether the unit	Stop recording. WNG54 #3		Fixed	19
and camera are properly
connected, and that electri
-city is on.
• Check whether the visual	Output video			41
signal is being properly	signals.
outputted.
• Check to see if there is a	Press the			27, 28
camera set for operation	WARNING			47-49
with no video signal input.	RESET button.

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• •••••••••••• •

96