JVC LPT1029-001A Video Connection, To connect to TV’s S-VIDEO input and Audio input, Connectors

18 EN INSTALLING YOUR NEW UNIT
Basic Connections						8 Basic Connection
						To connect to a TV with 21-pin SCART input connector ^
						A Disconnect the TV aerial cable from the TV.
						B Connect the TV aerial cable to the [ANTENNA IN] connector on
						the rear panel of the unit.
						C Connect the [ANTENNA OUT] connector on the rear panel of
						the unit and the TV’s aerial connector with the supplied RF
						cable.
						D Connect the [L-1 IN/OUT] connector on the rear panel of the
						unit and the TV’s 21-pin SCART connector with a supplied 21-
	TV aerial cable					pin SCART cable.
						● The [L-1 IN/OUT] connector accepts and delivers either a
						composite signal (regular video signal), Y/C signal or RGB
						signal.
						● Set your TV to the VIDEO (or AV), Y/C, or RGB mode
		To [ANTENNA IN]			Mains outlet	according to the type of your TV’s SCART connector.
						8 S-Video Connection
				Mains power cord		To connect to TV’s S-VIDEO input and AUDIO input
						connectors ^
						A Perform A – C in ABasic ConnectionB.
						B Connect the unit’s [S-VIDEO OUT] connector to the TV’s
						S-VIDEO input connector.
						C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO
						input connectors.
						● You can obtain high quality S-VHS pictures.
			To [L-1 IN/OUT]		Back of unit	● If your TV is not stereo capable, use the unit’s [AUDIO OUT]
						connectors to connect to an audio amplifier for Hi-Fi stereo
				To [AUDIO	To [S-VIDEO
						sound reproduction.
				OUT]	OUT]
						8 Component Video Connection
To			To [COMPONENT
[ANTENNA						To connect to TV’s component video input connectors ^
			VIDEO OUT (Y/PB/
OUT]						A Perform A – C in ABasic ConnectionB.
			PR)]	Audio cable
						B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
				(not supplied)	S-Video
						connectors to the TV’s component video input connectors.
			21-pin SCART		cable
RF cable						C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO
					(not supplied)
(supplied)			cable			input connectors.
			(supplied)
						● You can obtain high-quality component video pictures.
						● If your TV is not stereo-capable, use the unit’s [AUDIO OUT]
			Component			connectors to connect to an audio amplifier for Hi-Fistereo
			video cable			sound reproduction.
			(not supplied)			● By using the component video connection, you can view the
						images in the progressive mode. For switching to the
						progressive mode, refer to AScan Mode SetB (A pg. 73).
				TV		NOTE:
						Select an appropriate option of AL-1 OUTPUTB as follows
						(A pg. 66):
			To 75 ohm terminal			When your TV’s SCART
It’s essential that your unit be properly connected.							Set AL-1 OUTPUTB to:
						connector accepts:

ATTENTION:	Composite signals	ASCART VIDEOB
● Your TV must have a 21-pin AV input connector (SCART) for	Y/C signal (separated
the basic connection to the unit.	luminance (brightness) and	ASCART S-VIDEOB
● Connect the AC plug only after all connections to the TV has	chrominance (colour) signals)
been completed.
	RGB signal	ASCART RGBB
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO	Component video signal	ACOMPONENTB
OPERATION CAN BE PERFORMED.
	When the setting selected is not in accordance with the TV
1 Place the unit on a stable, horizontal surface.
	connected and depending on the type of appliance connected to
2 Connect the unit to a TV depending on the TV and cables you
	the unit, the correct picture will not appear.
use.	3 Plug the end of the mains power cord into a mains outlet.

● ALOADINGB blinks on the front display panel when the AC plug of the mains power cord is connected into a mains outlet and it takes approximately 50 seconds for the unit to be turned on.

This is not a malfunction.