Runco operation manual LS-3/LS-5 Specifications

Page 100

Specifications

Table 7-1. LS-3/LS-5 Specifications (continued)

 

Performance

 

 

Microdisplay:

Texas Instruments DLP® 1080p DMD

 

 

Native Resolution:

Full HD, 1920 x 1080 (2,073,600 pixels)

 

 

Aspect Ratios:

Native (Pixel-to-Pixel), 16:9, Letterbox, 4:3, 4:3 Narrow,

 

Letterbox (Anamorphic lens compatible)

 

 

Projection Lens:

All glass, F/2.5~2.71, f = 39.1~50.1mm, 1.3x manual

 

zoom, made in Japan

 

 

Throw Ratios:

1.85 – 2.40 (distance/width) – Standard lens

 

1.56 – 1.86 (distance/width) – Optional short-throw lens

 

 

Vertical Lens Shift Range

LS-3:

(Ceiling Mount):

Down = 25% to 60% of screen height below lens center

 

(50% to 120% of one half of the screen height)

 

LS-5:

 

Up = 25% of screen height above lens center

 

(50% of one half of the screen height)

 

Down = 60% of screen height below lens center

 

(120% of one half of the screen height)

 

 

Horizontal Lens Shift Range:

LS-3: None

 

LS-5:7.5% of screen width left or right of lens center

 

(15% of one half of the screen width)

 

 

Video Lumens:

1,000 ANSI lumens (maximum) calibrated at D65

 

 

Sequential Contrast –

LS-3:10,000:1 typical

ConstantContrast On:

LS-5:15,000:1 typical

 

 

Cooling Performance:

High efficiency adaptive voltage side-to-side cooling

 

with low system acoustic noise level and low light

 

pollution cabinet

 

 

Projection Modes:

Front, Rear, Ceiling (front/rear)

 

 

Lamp:

User replaceable 180/230W HPM (selectable), 4000

 

hour lifetime at 180W setting

 

 

Video Processing:

Runco advanced ViVix processing with 10 bit

 

independent dual channel image processing, true 1080i

 

deinterlacing, MPEG artifact reduction (block and

 

mosquito noise), latest motion adaptive processing, 3D

 

noise reduction, detail enhancement, rich color

 

processing and noise reduction, less than one frame

 

latency

 

 

Calibration:

Full RGB gain/offset control (White Balance), Gamma,

 

Contrast, Color Temperature, Brightness

 

 

84

Runco LS-3/LS-5 Installation/Operation Manual

Image 100
Contents LS-3 Series LS-5 Series LS-3 LS-3/CineWide LS-5 LS-5/CineWidePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsTable of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Additional Features of the LS-5 Controls and Functions LS-3/LS-5 at a GlanceSource LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page LS-3/LS-5 Remote Control Projector onPIP Remote Control InstallationOperation IR Reception Angles Quick Setup Installation OverviewStep Procedure For Details, ReferInstallation Projector Installation OptionsInstallation Type ConsiderationsAmbient Light Throw DistanceVertical and Horizontal Throw Ratios for the LS-3/LS-5 SeriesPosition Lens Shift Horizontal Lens Shift Example Only Folded Optics Installing the Optional CineWide Lens MountOther Considerations CineWide Base Plate Installing the FixedDo not use the mounting screws provided with the ceiling Mounting the LS-3/LS-5 Connections to Connector Panel AccessLS-3/LS-5 Connecting Source Components to the LS-3/LS-5 HDMI/DVI Connections See FigureRGB Connections Page 11. Composite and S-Video Connections RS-232 Controller ConnectionConnecting 12-Volt Connecting an External IRTrigger Output to External Theater EquipmentTurning on the Power Lens Adjustments Connecting to AC PowerFocus and Zoom Lens Shift Zoom Out Focus ZoomInstallation Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyAdjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input SourceUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus LS-3/LS-5 OSD Menu Structure Main LS-3/LS-5 Main MenuAspect Ratio Settings 169169 NarrowNative You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu Advanced LS-3/LS-5 Advanced MenuOperation X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation System 11. LS-3/LS-5 System Menu12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.crt Operations Control Commands Function Action on unit Lit.togSerial Commands Operation Commands ValuesSave.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status RS-232 Error Codes Error Code LED Indication DescriptionPage LS-3/LS-5 Specifications Dimensions Weight without lensOperating Temperature Universal Power SupplyLS-3/LS-5 Dimensions 1shows the LS-3/LS-5 dimensions, in millimetersSupported Signal Timings by Input Supported TimingsPAL-B/G