Runco LS-5, LS-3 operation manual Pal-B/G

Page 104

Specifications

Table 7-2. Supported Signal Timings by Input (continued)

		Refresh	Horizontal	Pixel Frequency		Supported? (√ = Yes, – = No)
			Horizontal
Format	Resolution		Frequency
Format	Resolution	Rate (Hz)	Frequency	(MHz)	RGB	Component 1	HDMI 1		Composite
		Rate (Hz)	(kHz)	(MHz)		Component 1	HDMI 1		Composite
			(kHz)			Component 2	HDMI 2		S-Video
						Component 2	HDMI 2		S-Video

1080/50p	1920x1080	50.00	56.250	148.500	√	√	√		–

1080/60p	1920x1080	59.94/60.00	67.433/67.500	148.350/148.500	√	√	√		–

NTSC 3.58	–	59.94/60.00	15.734/15.750	3.580	–	–	–		√

NTSC 4.43	–	59.94/60.00	15.734/15.750	4.430	–	–	–		√

PAL-B/G	–	50.00	15.625	4.430	–	–	–		√

PAL-M	–	59.94/60.00	15.734/15.750	3.580	–	–	–		√

PAL-N	–	50.00	15.625	3.580	–	–	–		√

PAL-60	–	59.94/60.00	15.734/15.750	4.430	–	–	–		√

SECAM	–	50.00	13.500	4.250/4.410	–	–	–		√

88	Runco LS-3/LS-5 Installation/Operation Manual

Image 104

Contents LS-3 Series LS-5 Series LS-3 LS-3/CineWide LS-5 LS-5/CineWidePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsTable of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Additional Features of the LS-5 Controls and Functions LS-3/LS-5 at a GlanceSource LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page LS-3/LS-5 Remote Control Projector onPIP Operation InstallationRemote Control IR Reception Angles Quick Setup Installation OverviewStep Procedure For Details, ReferInstallation Projector Installation OptionsInstallation Type ConsiderationsAmbient Light Throw DistancePosition Throw Ratios for the LS-3/LS-5 SeriesVertical and Horizontal Lens Shift Horizontal Lens Shift Example Only Other Considerations Installing the Optional CineWide Lens MountFolded Optics Do not use the mounting screws provided with the ceiling Installing the FixedCineWide Base Plate Mounting the LS-3/LS-5 LS-3/LS-5 Connector Panel AccessConnections to Connecting Source Components to the LS-3/LS-5 HDMI/DVI Connections See FigureRGB Connections Page 11. Composite and S-Video Connections RS-232 Controller ConnectionConnecting 12-Volt Connecting an External IRTrigger Output to External Theater EquipmentTurning on the Power Lens Adjustments Connecting to AC PowerFocus and Zoom Lens Shift Zoom Out Focus ZoomInstallation Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyAdjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input SourceUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus LS-3/LS-5 OSD Menu Structure Main LS-3/LS-5 Main MenuAspect Ratio Settings 169169 NarrowNative You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu Advanced LS-3/LS-5 Advanced MenuOperation X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation System 11. LS-3/LS-5 System Menu12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.crt Operations Control Commands Function Action on unit Lit.togSerial Commands Operation Commands ValuesSave.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status RS-232 Error Codes Error Code LED Indication DescriptionPage LS-3/LS-5 Specifications Dimensions Weight without lensOperating Temperature Universal Power SupplyLS-3/LS-5 Dimensions 1shows the LS-3/LS-5 dimensions, in millimetersSupported Signal Timings by Input Supported TimingsPAL-B/G