Runco LS-3 Turning on the Power Lens Adjustments, Connecting to AC Power, Zoom Out Focus Zoom

Page 47

Installation

The LS-3/LS-5 ships with various types of AC power cords. Choose the one that is	Connecting to AC Power
appropriate to your locale.

Plug the female end of the power cord into the AC receptacle on the rear of the projector (AC 100V ~ 240V); see Figure 2-3. Then, connect the other end to your AC power source.

1. Turn on your source components.

ON

2. Press the ON l button on the remote control to turn on the LS-3/LS-5. The LED flashes green to indicate that it is warming up.

3. When the projector is ready for use, the LED turns off.

The LS-3/LS-5 gives you a great deal of control over the picture size, position and focus.

3.7

Turning on the Power

3.8

Lens Adjustments

To focus the projected image, grasp the lens by the front ring and rotate it.

To make the picture smaller (zoom out) or larger (zoom in), rotate the zoom ring in the appropriate direction.

To access the lens shift controls:

1.Locate the Runco badge at the top of the projector. Press on the side of the badge nearest the “R” to release it.

Zoom Out

Focus Zoom In

Focus and Zoom

Lens Shift

2.Carefully lift the badge up, then away from the projector.

Runco LS-3/LS-5 Installation/Operation Manual

31

Image 47

Contents LS-3 LS-3/CineWide LS-5 LS-5/CineWide LS-3 Series LS-5 SeriesPage RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingSerial Communications SpecificationsTable of Contents Xiv List of Figures List of Figures Xvi About This Manual IntroductionIf you need Turn to Using This ManualDescription, Features and Benefits Additional Features of the LS-5 LS-3/LS-5 at a Glance Controls and FunctionsSource LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page Projector on LS-3/LS-5 Remote ControlPIP Operation InstallationRemote Control IR Reception Angles For Details, Refer Quick SetupInstallation Overview Step ProcedureConsiderations InstallationProjector Installation Options Installation TypeThrow Distance Ambient LightPosition Throw Ratios for the LS-3/LS-5 SeriesVertical and Horizontal Lens Shift Horizontal Lens Shift Example Only Other Considerations Installing the Optional CineWide Lens MountFolded Optics Do not use the mounting screws provided with the ceiling Installing the FixedCineWide Base Plate Mounting the LS-3/LS-5 LS-3/LS-5 Connector Panel AccessConnections to HDMI/DVI Connections See Figure Connecting Source Components to the LS-3/LS-5RGB Connections Page 11. Composite and S-Video Connections Connection RS-232 ControllerTheater Equipment Connecting 12-VoltConnecting an External IR Trigger Output to ExternalZoom Out Focus Zoom Turning on the Power Lens AdjustmentsConnecting to AC Power Focus and Zoom Lens ShiftInstallation Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAdjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect RatioMain Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus LS-3/LS-5 OSD Menu Structure LS-3/LS-5 Main Menu Main169 Aspect Ratio SettingsNarrow 169Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-3/LS-5 Advanced Menu AdvancedOperation Color X/y Color Gamut ValuesRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation 11. LS-3/LS-5 System Menu System12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.crt Lit.tog Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsSave.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status Error Code LED Indication Description RS-232 Error CodesPage LS-3/LS-5 Specifications Universal Power Supply DimensionsWeight without lens Operating Temperature1shows the LS-3/LS-5 dimensions, in millimeters LS-3/LS-5 DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G