Runco LS-5, LS-3 operation manual PIP Split-Screen Mode

Page 76

Operation

Figure 4-14. PIP Split-Screen Mode

Menu Position: Select Menu Position from the System menu to change the OSD menu position. The default setting is ““ (top left).

Translucent Menu: Select Translucent Menu from the System menu to adjust the degree of translucence (show-through) in the menus and message boxes. 0% means that the menus are opaque. The default setting is 25%.

Lamp Power: Select Lamp Power from the System menu to adjust the lamp output level. You can choose to run the lamp as bright as possible (230W; this is the default setting) or you can choose the Economy (180W) setting. Generally, lower lamp output prolongs the life of the lamp, but decreases brightness. This setting is per source, not global, so it can be saved like other user settings.

Blank Screen: Select Blank Screen from the System menu to choose the color of the blank screen that appears when no source signal is present. The options are Black, Blue and White. The default is Black.

Auto Power Off: Set Auto Power Off to On to have the LS-3/LS-5 turn itself off after 20 minutes of inactivity (no source signal present).

Auto Power On: Setting Auto Power On to On causes the projector to automatically power up when AC power is present. If the projector is plugged into a switched AC outlet, this allows the projector to be turned on using a wall switch instead of the remote control unit. If you do not need this capability, set Auto Power On to Off (this is the default setting).

Rear Projection: This control reverses all images and menus, and is necessary when the projector is used in rear-projection applications. The default is Off.

Ceiling Mode: This control flips the image so the projector can be used in ceiling mounted installations. The default setting, Auto, automatically determines the orientation using an internal sensor.

Power On Chime: This controls the audible chime at startup.

60	Runco LS-3/LS-5 Installation/Operation Manual

Image 76

Contents LS-3 Series LS-5 Series LS-3 LS-3/CineWide LS-5 LS-5/CineWidePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsTable of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Additional Features of the LS-5 Controls and Functions LS-3/LS-5 at a GlanceSource LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page LS-3/LS-5 Remote Control Projector onPIP Remote Control InstallationOperation IR Reception Angles Quick Setup Installation OverviewStep Procedure For Details, ReferInstallation Projector Installation OptionsInstallation Type ConsiderationsAmbient Light Throw DistanceVertical and Horizontal Throw Ratios for the LS-3/LS-5 SeriesPosition Lens Shift Horizontal Lens Shift Example Only Folded Optics Installing the Optional CineWide Lens MountOther Considerations CineWide Base Plate Installing the FixedDo not use the mounting screws provided with the ceiling Mounting the LS-3/LS-5 Connections to Connector Panel AccessLS-3/LS-5 Connecting Source Components to the LS-3/LS-5 HDMI/DVI Connections See FigureRGB Connections Page 11. Composite and S-Video Connections RS-232 Controller ConnectionConnecting 12-Volt Connecting an External IRTrigger Output to External Theater EquipmentTurning on the Power Lens Adjustments Connecting to AC PowerFocus and Zoom Lens Shift Zoom Out Focus ZoomInstallation Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properlyAdjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input SourceUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus LS-3/LS-5 OSD Menu Structure Main LS-3/LS-5 Main MenuAspect Ratio Settings 169169 NarrowNative You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu Advanced LS-3/LS-5 Advanced MenuOperation X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation System 11. LS-3/LS-5 System Menu12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.crt Operations Control Commands Function Action on unit Lit.togSerial Commands Operation Commands ValuesSave.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status RS-232 Error Codes Error Code LED Indication DescriptionPage LS-3/LS-5 Specifications Dimensions Weight without lensOperating Temperature Universal Power SupplyLS-3/LS-5 Dimensions 1shows the LS-3/LS-5 dimensions, in millimetersSupported Signal Timings by Input Supported TimingsPAL-B/G