Runco LS-10I Home Theater Calibration Specifications, Industry-Standard Specifications

Page 107

Specifications

Table 7-1. LS-10i Specifications (continued)

Brightness and Contrast:

Weight (without lens): Regulatory Approvals:

Limited Warranty:

Cinema Standards Measurement System (CSMS) Specifications

-Brightness: 119 foot-Lamberts (fL)

-Contrast Ratio: 251:1

These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter, Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6,500K and has a minimum of 150 hours of usage.

The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen surface. The Society of Motion Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light output.

Home Theater Calibration Specifications

-Light Output: 1845 ANSI Lumens

-Contrast Ratio: 251:1

These specifications are obtained by calibrating the projector as described above for CSMS measurements.

Industry-Standard Specifications

-Light Output: 2100 ANSI Lumens

-Contrast Ratio: 10,000:1 full-on, full-off (dynamic)

These are typical projector brightness and contrast specifications found in most companies’ sales literature. Runco includes these measurements in its literature to allow for direct comparison with other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance data when the projector is used in professional, commercial and industrial displays.

40.8 lbs. (18.50 kg)

FCC Part 15 Class B, CE Class B, UL, cUL, CB, RoHS, WEEE, local conformances as required

Projector: Two (2) years parts and labor from the date of shipment from Runco. RuncoCare™ and Runco RedCarpet™ plans are also available.

Lamp: 1000 hours or six (6) months, whichever comes first.

Specifications are subject to change without notice.

Runco LS-10i Installation/Operation Manual

91

Image 107

Contents LS-10i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation External Control Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualFormat screen Description, Features and BenefitsOptional Accessories Press this button to show or hide the OSD menus Controls and FunctionsLS-10i at a Glance Cursor KeysExhaust Vent Runco Logo Badge Rear Cover RGB LS-10i Rear PanelLS-10i Remote Control COL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastVwide VirtualWide Aspect Ratio Selection Buttons169 Lbox LetterboxControls and Functions Remote Control InstallationIR Reception Angles For Details, Refer Quick SetupInstallation Overview Step ProcedureConsiderations InstallationProjector Installation Options Installation TypeEstimating Throw Distance Ambient LightThrow Distance Lens LS-10i Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with Lens OptionPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example Only Folded Optics Other Considerations Installing the Optional Anamorphic Lens MountPackage Contents Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the ScrewsPlate Installation Mounting the LS-10i Angle Adjusting the ProjectionConnections to the LS-10i Connector Panel AccessHDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etc Connecting SourceComponents to the LS-10i HDMI/DVI Connections See FigureComputer RGB Camcorder Gaming Console 10. Scart Source ConnectionsDTV-Set-Top Box 11. Component Video Connections12. Composite and S-Video Connections Camcorder Gaming ConsoleConnection RS-232 Controller+12V Trigger Input Connecting 12-VoltTrigger Output to External Theater EquipmentAppropriate to your locale Connecting an External IRConnecting to AC Power ReceiverFocus Zoom Lens Shift Turning on the Power Primary Lens AdjustmentsRear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationInstallation See Figure Adjustment Installing and Adjusting the Anamorphic LensAdjusting the Lens Position Installation Selecting An Aspect Ratio Selecting Video Memory OperationSelecting An Input SourceMain Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus LS-10i Main Menu Letterbox Aspect Ratio Settings169 Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu LS-10i Advanced Menu AdvancedPCE Color Gamut setting refer to Color Gamut, below Color X/y Color Gamut ValuesRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Magenta Blue Gre en Yellow Cy anRed 13. LS-10i System Menu 14. Input Enable Sub-Menu Top right 921x51816. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting Serial Communications RS-232 Connection Port Configuration Serial Command SyntaxExternal Control Apply 169 aspect ratio Serial Command Key Names and IR CodesSome key command examples Switch to next user memoryRemote Button IR Code RS232 Keyname0x08 = value Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsColor.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 Error Code LED Indication Description RS-232 Error CodesOpcode Value Using Hdmi CEC MessagesCEC Commands Supported by the LS-10i CEC Command ListInactive Source 0x9D CEC Version Proteus 1 None Proteus 2, 3, 4, 5 SpecificationsLS-10i Specifications LS-10i SpecificationsHDTV, EDTV, Sdtv Specifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications LS-10i Dimensions LS-10i DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page 020-1075-00 Rev. a September