Runco LS-10I operation manual PCE Sub-Menu

Page 76

Operation

•Tracking (RGB or Component sources): Tracking determines the frequency of the pixel sampling clock, indicated by the number of incoming pixels per line, so that all pixels generated by a particular source are sampled.

Steady flickering or several soft vertical stripes or bands across the entire image indicates poor pixel tracking. Proper pixel tracking helps ensure that the image quality is consistent across the screen, that aspect ratio is maintained and that pixel phase (see above) can be optimized.

•Sync Level (Component sources only): Select Sync Level to adjust the voltage level of the LS-10i Sync signal detection circuitry.

Sync Level adjustment is occasionally necessary when a DVD player or HDTV source signal drops “below black” (for example, during scenes with explosions or when subtitles are present) and causes the projector to temporarily lose sync. If the Sync Level from the source is persistently too low, the projector won’t sync with the source at all.

The range is from 50 to 256 millivolts (mV) inclusive. The default setting is 240 mV and should rarely require adjustment.

PCE: To use the Personal Color Equalizer to define a custom color gamut, choose the “PCE” Color Gamut setting (refer to Color Gamut on page 57). Then, choose PCE from the Advanced menu and press ENTER. This displays the PCE sub-menu, shown in Figure 4-11.

Figure 4-11. PCE Sub-Menu

60	Runco LS-10i Installation/Operation Manual

Image 76

Contents LS-10i Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Controls and Functions LS-10i at a GlanceCursor Keys Press this button to show or hide the OSD menusExhaust Vent Runco Logo Badge Rear Cover LS-10i Rear Panel RGBLS-10i Remote Control Picture Adjustment Buttons BRT Brightness Memory Preset ButtonsContrast COL ColorAspect Ratio Selection Buttons 169Lbox Letterbox Vwide VirtualWideControls and Functions Installation Remote ControlIR Reception Angles Quick Setup Installation OverviewStep Procedure For Details, ReferInstallation Projector Installation OptionsInstallation Type ConsiderationsThrow Distance Ambient LightEstimating Throw Distance LS-10i Lens Options and Throw Ratios Note Throw Range Throw Ratio Inches, withLens Option LensCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example Only Package Contents Installing the Optional Anamorphic Lens MountFolded Optics Other Considerations Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Do not OVER-TIGHTEN the Screws Ceiling Mount Plate Attachment Plate Projector bottomPlate Installation Mounting the LS-10i Adjusting the Projection AngleConnector Panel Access Connections to the LS-10iConnecting Source Components to the LS-10iHDMI/DVI Connections See Figure HDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etcComputer RGB Camcorder 10. Scart Source Connections Gaming Console11. Component Video Connections DTV-Set-Top BoxCamcorder Gaming Console 12. Composite and S-Video ConnectionsRS-232 Controller ConnectionConnecting 12-Volt Trigger Output to ExternalTheater Equipment +12V Trigger InputConnecting an External IR Connecting to AC PowerReceiver Appropriate to your localeTurning on the Power Primary Lens Adjustments Focus Zoom Lens ShiftChanging the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the Anamorphic Lens Installation See Figure AdjustmentAdjusting the Lens Position Installation Operation Selecting An InputSource Selecting An Aspect Ratio Selecting Video MemoryUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus LS-10i Main Menu 169 Aspect Ratio SettingsLetterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu Advanced LS-10i Advanced MenuPCE Color Gamut setting refer to Color Gamut, below X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Red Gre en Yellow Cy anMagenta Blue 13. LS-10i System Menu 14. Input Enable Sub-Menu 921x518 Top right16. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting External Control RS-232 Connection Port Configuration Serial Command SyntaxSerial Communications Serial Command Key Names and IR Codes Some key command examplesSwitch to next user memory Apply 169 aspect ratioIR Code RS232 Keyname Remote Button0x08 Operations Control Commands Function Action on unit = valueSerial Commands Operation Commands ValuesColor.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 RS-232 Error Codes Error Code LED Indication DescriptionUsing Hdmi CEC Messages CEC Commands Supported by the LS-10iCEC Command List Opcode ValueInactive Source 0x9D CEC Version Specifications LS-10i SpecificationsLS-10i Specifications Proteus 1 None Proteus 2, 3, 4, 5HDTV, EDTV, Sdtv Industry-Standard Specifications Home Theater Calibration SpecificationsSpecifications are subject to change without notice LS-10i Dimensions LS-10i DimensionsSupported Signal Timings by Input Supported TimingsPAL-B/G Page 020-1075-00 Rev. a September