Runco LS-10I operation manual Exhaust Vent

Page 22

Controls and Functions

•POWER BUTTON/STATUS LED Indicates projector status as follows:

• Solid green = AC power present, ready to turn on (lamp not lit)

•Flashing green = lamp is warming up or cooling down; keypad functions not allowed

•Off = Lamp lit, projector functioning normally

•Alternating green/red = Lamp problem (door open, unable to strike, end of life), user intervention likely to fix problem

•Flashing red = Over temperature, user intervention (clear vents, turn on AC) may fix problem

•Solid red = Error that requires servicing (fan fail, Power-on self-test fail etc.)

•EXHAUST VENT

Warm air exits the projector through this vent. Ensure that it is not blocked.

•INTAKE VENT

Internal fans draw cool air into the projector through this vent.

•PROJECTION LENS

If needed, a light shield accessory is provided with the lens to minimize stray light emissions. (Use it only when the vertical offset is 50% of the screen height or greater.) The light shield attaches to the end of the lens.

•FRONT IR SENSOR

Receives infrared signals from the remote control unit.

6	Runco LS-10i Installation/Operation Manual

Image 22

Contents LS-10i Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Cursor Keys Controls and FunctionsLS-10i at a Glance Press this button to show or hide the OSD menusExhaust Vent Runco Logo Badge Rear Cover LS-10i Rear Panel RGBLS-10i Remote Control Contrast Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons COL ColorLbox Letterbox Aspect Ratio Selection Buttons169 Vwide VirtualWideControls and Functions Installation Remote ControlIR Reception Angles Step Procedure Quick SetupInstallation Overview For Details, ReferInstallation Type InstallationProjector Installation Options ConsiderationsThrow Distance Ambient LightEstimating Throw Distance Lens Option LS-10i Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with LensVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example Only Package Contents Installing the Optional Anamorphic Lens MountFolded Optics Other Considerations Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Do not OVER-TIGHTEN the Screws Ceiling Mount Plate Attachment Plate Projector bottomPlate Installation Mounting the LS-10i Adjusting the Projection AngleConnector Panel Access Connections to the LS-10iHDMI/DVI Connections See Figure Connecting SourceComponents to the LS-10i HDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etcComputer RGB Camcorder 10. Scart Source Connections Gaming Console11. Component Video Connections DTV-Set-Top BoxCamcorder Gaming Console 12. Composite and S-Video ConnectionsRS-232 Controller ConnectionTheater Equipment Connecting 12-VoltTrigger Output to External +12V Trigger InputReceiver Connecting an External IRConnecting to AC Power Appropriate to your localeTurning on the Power Primary Lens Adjustments Focus Zoom Lens ShiftChanging the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the Anamorphic Lens Installation See Figure AdjustmentAdjusting the Lens Position Installation Source OperationSelecting An Input Selecting An Aspect Ratio Selecting Video MemoryPIP Input Source Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations MainUsing the On-Screen Menus LS-10i Main Menu 169 Aspect Ratio SettingsLetterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu Advanced LS-10i Advanced MenuPCE Color Gamut setting refer to Color Gamut, below X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Red Gre en Yellow Cy anMagenta Blue 13. LS-10i System Menu 14. Input Enable Sub-Menu 921x518 Top right16. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting External Control RS-232 Connection Port Configuration Serial Command SyntaxSerial Communications Switch to next user memory Serial Command Key Names and IR CodesSome key command examples Apply 169 aspect ratioIR Code RS232 Keyname Remote Button0x08 Operations Control Commands Function Action on unit = valueSerial Commands Operation Commands ValuesColor.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 RS-232 Error Codes Error Code LED Indication DescriptionCEC Command List Using Hdmi CEC MessagesCEC Commands Supported by the LS-10i Opcode ValueInactive Source 0x9D CEC Version LS-10i Specifications SpecificationsLS-10i Specifications Proteus 1 None Proteus 2, 3, 4, 5HDTV, EDTV, Sdtv Industry-Standard Specifications Home Theater Calibration SpecificationsSpecifications are subject to change without notice LS-10i Dimensions LS-10i DimensionsSupported Signal Timings by Input Supported TimingsPAL-B/G Page 020-1075-00 Rev. a September