Runco LS-10I operation manual Attaching the Transport Assembly Attachment Plate

Page 38

Installation

•Transport Assembly Attachment Plate

•Attachment plate hardware (screws, washers and spacers)

•Attachment plate security hooks and related hardware (chain, chain ends, nuts and washers)

•Transport Assembly

•Transport mounting hardware

•Lens bracket mounting hardware

•Power supply

•Remote control unit and batteries

•Anamorphic lens and mounting bracket

Attaching the Transport Assembly Attachment Plate:

1. Place the projector upside down on a blanket or other soft surface.

22	Runco LS-10i Installation/Operation Manual

Image 38

Contents LS-10i Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation External Control Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Cursor Keys Controls and FunctionsLS-10i at a Glance Press this button to show or hide the OSD menusExhaust Vent Runco Logo Badge Rear Cover LS-10i Rear Panel RGBLS-10i Remote Control Contrast Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons COL ColorLbox Letterbox Aspect Ratio Selection Buttons169 Vwide VirtualWideControls and Functions Installation Remote ControlIR Reception Angles Step Procedure Quick SetupInstallation Overview For Details, ReferInstallation Type InstallationProjector Installation Options ConsiderationsEstimating Throw Distance Ambient LightThrow Distance Lens Option LS-10i Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with LensVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example Only Folded Optics Other Considerations Installing the Optional Anamorphic Lens MountPackage Contents Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Do not OVER-TIGHTEN the Screws Ceiling Mount Plate Attachment Plate Projector bottomPlate Installation Mounting the LS-10i Adjusting the Projection AngleConnector Panel Access Connections to the LS-10iHDMI/DVI Connections See Figure Connecting SourceComponents to the LS-10i HDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etcComputer RGB Camcorder 10. Scart Source Connections Gaming Console11. Component Video Connections DTV-Set-Top BoxCamcorder Gaming Console 12. Composite and S-Video ConnectionsRS-232 Controller ConnectionTheater Equipment Connecting 12-VoltTrigger Output to External +12V Trigger InputReceiver Connecting an External IRConnecting to AC Power Appropriate to your localeTurning on the Power Primary Lens Adjustments Focus Zoom Lens ShiftChanging the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling ModeInstalling and Adjusting the Anamorphic Lens Installation See Figure AdjustmentAdjusting the Lens Position Installation Source OperationSelecting An Input Selecting An Aspect Ratio Selecting Video MemoryPIP Input Source Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations MainUsing the On-Screen Menus LS-10i Main Menu Letterbox Aspect Ratio Settings169 Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu Advanced LS-10i Advanced MenuPCE Color Gamut setting refer to Color Gamut, below X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Magenta Blue Gre en Yellow Cy anRed 13. LS-10i System Menu 14. Input Enable Sub-Menu 921x518 Top right16. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting Serial Communications RS-232 Connection Port Configuration Serial Command SyntaxExternal Control Switch to next user memory Serial Command Key Names and IR CodesSome key command examples Apply 169 aspect ratioIR Code RS232 Keyname Remote Button0x08 Operations Control Commands Function Action on unit = valueSerial Commands Operation Commands ValuesColor.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 RS-232 Error Codes Error Code LED Indication DescriptionCEC Command List Using Hdmi CEC MessagesCEC Commands Supported by the LS-10i Opcode ValueInactive Source 0x9D CEC Version LS-10i Specifications SpecificationsLS-10i Specifications Proteus 1 None Proteus 2, 3, 4, 5HDTV, EDTV, Sdtv Specifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications LS-10i Dimensions LS-10i DimensionsSupported Signal Timings by Input Supported TimingsPAL-B/G Page 020-1075-00 Rev. a September