Runco LS-10I operation manual Connections to the LS-10i, Connector Panel Access

Page 45

Installation

Proceed as follows to connect the LS-10i to your video sources, external controller(s) – if present – and AC power.

When connecting your equipment:

•Use the correct signal cables for each source.

•Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them.

Using a flat-blade screwdriver, loosen the two screws holding the rear compartment cover in place.

Then, remove the rear compartment cover by tilting it upward.

3.6

Connections to the LS-10i

Connector Panel Access

Runco LS-10i Installation/Operation Manual

29

Image 45

Contents LS-10i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsExternal Control Table of Contents Xiv List of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualFormat screen Description, Features and BenefitsOptional Accessories LS-10i at a Glance Controls and FunctionsCursor Keys Press this button to show or hide the OSD menusExhaust Vent Runco Logo Badge Rear Cover RGB LS-10i Rear PanelLS-10i Remote Control Memory Preset Buttons Picture Adjustment Buttons BRT BrightnessContrast COL Color169 Aspect Ratio Selection ButtonsLbox Letterbox Vwide VirtualWideControls and Functions Remote Control InstallationIR Reception Angles Installation Overview Quick SetupStep Procedure For Details, ReferProjector Installation Options InstallationInstallation Type ConsiderationsAmbient Light Throw DistanceEstimating Throw Distance Throw Range Throw Ratio Inches, with LS-10i Lens Options and Throw Ratios NoteLens Option LensFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example Only Installing the Optional Anamorphic Lens Mount Package ContentsFolded Optics Other Considerations Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the ScrewsPlate Installation Mounting the LS-10i Angle Adjusting the ProjectionConnections to the LS-10i Connector Panel AccessComponents to the LS-10i Connecting SourceHDMI/DVI Connections See Figure HDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etcComputer RGB Camcorder Gaming Console 10. Scart Source ConnectionsDTV-Set-Top Box 11. Component Video Connections12. Composite and S-Video Connections Camcorder Gaming ConsoleConnection RS-232 ControllerTrigger Output to External Connecting 12-VoltTheater Equipment +12V Trigger InputConnecting to AC Power Connecting an External IRReceiver Appropriate to your localeFocus Zoom Lens Shift Turning on the Power Primary Lens AdjustmentsRear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationInstallation See Figure Adjustment Installing and Adjusting the Anamorphic LensAdjusting the Lens Position Installation Selecting An Input OperationSource Selecting An Aspect Ratio Selecting Video MemoryAvailable Main and PIP Source Combinations Using Picture-In-Picture PIPPIP Input Source MainUsing the On-Screen Menus LS-10i Main Menu Aspect Ratio Settings 169Letterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu LS-10i Advanced Menu AdvancedPCE Color Gamut setting refer to Color Gamut, below Color X/y Color Gamut ValuesRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Gre en Yellow Cy an RedMagenta Blue 13. LS-10i System Menu 14. Input Enable Sub-Menu Top right 921x51816. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting RS-232 Connection Port Configuration Serial Command Syntax External ControlSerial Communications Some key command examples Serial Command Key Names and IR CodesSwitch to next user memory Apply 169 aspect ratioRemote Button IR Code RS232 Keyname0x08 = value Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsColor.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 Error Code LED Indication Description RS-232 Error CodesCEC Commands Supported by the LS-10i Using Hdmi CEC MessagesCEC Command List Opcode ValueInactive Source 0x9D CEC Version LS-10i Specifications SpecificationsLS-10i Specifications Proteus 1 None Proteus 2, 3, 4, 5HDTV, EDTV, Sdtv Home Theater Calibration Specifications Industry-Standard SpecificationsSpecifications are subject to change without notice LS-10i Dimensions LS-10i DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page 020-1075-00 Rev. a September