Runco LS-10I operation manual Fine Sync Sub-Menu

Page 75

Operation

Fine Sync: To fine-tune the position and other image attributes, choose Fine Sync from the Advanced menu and press ENTER. This displays the Fine Sync sub-menu, shown in Figure 4-10.

Figure 4-10. Fine Sync Sub-Menu

•V Position: This control adjusts the vertical position of the image within the designated image area, up to 25 per cent of the image height up or down.

•H Position: This control adjusts the horizontal position of the image within the designated image area, up to 25 per cent of the image width left or right.

•Phase (RGB or Component sources): This control adjusts the phase of the pixel sampling clock relative to the incoming signal. Adjust the phase when an RGB or Component image still shows shimmer or “noise” after Tracking has been optimized.

Adjust the Phase after adjusting Tracking (see below). If some

Tip shimmer from a video or HDTV source persists, use the Noise Reduction controls (described on page 52) to remove high-frequency noise from the signal.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. Adjust the slidebar until the image stabilizes and each pixel is clearly defined. You may notice that you can stabilize the image at more than one point. Use either setting in such cases.

Runco LS-10i Installation/Operation Manual

59

Image 75

Contents LS-10i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsExternal Control Table of Contents Xiv List of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualFormat screen Description, Features and BenefitsOptional Accessories Press this button to show or hide the OSD menus Controls and FunctionsLS-10i at a Glance Cursor KeysExhaust Vent Runco Logo Badge Rear Cover RGB LS-10i Rear PanelLS-10i Remote Control COL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastVwide VirtualWide Aspect Ratio Selection Buttons169 Lbox LetterboxControls and Functions Remote Control InstallationIR Reception Angles For Details, Refer Quick SetupInstallation Overview Step ProcedureConsiderations InstallationProjector Installation Options Installation TypeAmbient Light Throw DistanceEstimating Throw Distance Lens LS-10i Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with Lens OptionPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example Only Installing the Optional Anamorphic Lens Mount Package ContentsFolded Optics Other Considerations Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the ScrewsPlate Installation Mounting the LS-10i Angle Adjusting the ProjectionConnections to the LS-10i Connector Panel AccessHDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etc Connecting SourceComponents to the LS-10i HDMI/DVI Connections See FigureComputer RGB Camcorder Gaming Console 10. Scart Source ConnectionsDTV-Set-Top Box 11. Component Video Connections12. Composite and S-Video Connections Camcorder Gaming ConsoleConnection RS-232 Controller+12V Trigger Input Connecting 12-VoltTrigger Output to External Theater EquipmentAppropriate to your locale Connecting an External IRConnecting to AC Power ReceiverFocus Zoom Lens Shift Turning on the Power Primary Lens AdjustmentsRear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationInstallation See Figure Adjustment Installing and Adjusting the Anamorphic LensAdjusting the Lens Position Installation Selecting An Aspect Ratio Selecting Video Memory OperationSelecting An Input SourceMain Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus LS-10i Main Menu Aspect Ratio Settings 169Letterbox Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu LS-10i Advanced Menu AdvancedPCE Color Gamut setting refer to Color Gamut, below Color X/y Color Gamut ValuesRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Gre en Yellow Cy an RedMagenta Blue 13. LS-10i System Menu 14. Input Enable Sub-Menu Top right 921x51816. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting RS-232 Connection Port Configuration Serial Command Syntax External ControlSerial Communications Apply 169 aspect ratio Serial Command Key Names and IR CodesSome key command examples Switch to next user memoryRemote Button IR Code RS232 Keyname0x08 = value Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsColor.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 Error Code LED Indication Description RS-232 Error CodesOpcode Value Using Hdmi CEC MessagesCEC Commands Supported by the LS-10i CEC Command ListInactive Source 0x9D CEC Version Proteus 1 None Proteus 2, 3, 4, 5 SpecificationsLS-10i Specifications LS-10i SpecificationsHDTV, EDTV, Sdtv Home Theater Calibration Specifications Industry-Standard SpecificationsSpecifications are subject to change without notice LS-10i Dimensions LS-10i DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page 020-1075-00 Rev. a September