Runco LS-10I Vertical and Horizontal, Position, Ceiling Installation, Floor Installation

Page 35

Installation

Proper placement of the projector relative to the screen will yield a rectangular,	Vertical and Horizontal
perfectly-centered image that completely fills the screen.	Position
Ideally, the projector should be positioned perpendicular to the screen and in such a way
that the lens center is aligned with either the top or bottom edge of the screen area, and
centered horizontally. See Figure 3-3.

Ceiling Installation

Ceiling

Height	Projection Distance

x

Lens Center

Lens Center

Screen

Floor Installation

Height

Lens Center

x

Screen

Lens Center

Projection Distance

Floor

Figure 3-3. Projector Placement
You can use the lens shift controls on the projector to center the image on the screen.	Lens Shift
Lens shift is generally expressed as a percentage of the screen height or width, as shown
in Figure 3-4and Figure 3-5.

Screen Center

0%

50% Height

Lens Shift

(0.5 x H)

100% Height

Lens Shift

(1.0 x H)

Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular

lens or projector is used in this example.

Figure 3-4. Vertical Lens Shift (Example Only)

Runco LS-10i Installation/Operation Manual

19

Image 35

Contents LS-10i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation External Control Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualFormat screen Description, Features and BenefitsOptional Accessories Press this button to show or hide the OSD menus Controls and FunctionsLS-10i at a Glance Cursor KeysExhaust Vent Runco Logo Badge Rear Cover RGB LS-10i Rear PanelLS-10i Remote Control COL Color Picture Adjustment Buttons BRT BrightnessMemory Preset Buttons ContrastVwide VirtualWide Aspect Ratio Selection Buttons169 Lbox LetterboxControls and Functions Remote Control InstallationIR Reception Angles For Details, Refer Quick SetupInstallation Overview Step ProcedureConsiderations InstallationProjector Installation Options Installation TypeEstimating Throw Distance Ambient LightThrow Distance Lens LS-10i Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with Lens OptionPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example Only Folded Optics Other Considerations Installing the Optional Anamorphic Lens MountPackage Contents Attaching the Transport Assembly Attachment Plate Position the attachment plate as shown here Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the ScrewsPlate Installation Mounting the LS-10i Angle Adjusting the ProjectionConnections to the LS-10i Connector Panel AccessHDMI/DVI sources BD, DVD DTV Set-Top Box, Game Console etc Connecting SourceComponents to the LS-10i HDMI/DVI Connections See FigureComputer RGB Camcorder Gaming Console 10. Scart Source ConnectionsDTV-Set-Top Box 11. Component Video Connections12. Composite and S-Video Connections Camcorder Gaming ConsoleConnection RS-232 Controller+12V Trigger Input Connecting 12-VoltTrigger Output to External Theater EquipmentAppropriate to your locale Connecting an External IRConnecting to AC Power ReceiverFocus Zoom Lens Shift Turning on the Power Primary Lens AdjustmentsRear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationInstallation See Figure Adjustment Installing and Adjusting the Anamorphic LensAdjusting the Lens Position Installation Selecting An Aspect Ratio Selecting Video Memory OperationSelecting An Input SourceMain Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus LS-10i Main Menu Letterbox Aspect Ratio Settings169 Virtual Cinema You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Overscan Examples Input Select Sub-Menu LS-10i Advanced Menu AdvancedPCE Color Gamut setting refer to Color Gamut, below Color X/y Color Gamut ValuesRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. PCE Sub-Menu Magenta Blue Gre en Yellow Cy anRed 13. LS-10i System Menu 14. Input Enable Sub-Menu Top right 921x51816. PIP Split-Screen Mode 17. LS-10i Control Menu Language 18. LS-10i Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Troubleshooting Chart Maintenance and Troubleshooting Serial Communications RS-232 Connection Port Configuration Serial Command SyntaxExternal Control Apply 169 aspect ratio Serial Command Key Names and IR CodesSome key command examples Switch to next user memoryRemote Button IR Code RS232 Keyname0x08 = value Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsColor.space = ? Vert.pos = ? + Key = ? Cinewide = ? Cal.text1 Error Code LED Indication Description RS-232 Error CodesOpcode Value Using Hdmi CEC MessagesCEC Commands Supported by the LS-10i CEC Command ListInactive Source 0x9D CEC Version Proteus 1 None Proteus 2, 3, 4, 5 SpecificationsLS-10i Specifications LS-10i SpecificationsHDTV, EDTV, Sdtv Specifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications LS-10i Dimensions LS-10i DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page 020-1075-00 Rev. a September