TacT Audio owner manual Update the RCS 2.0S Firmware

Page 33

Step I: Removing your old RCS 2.0S Software

Step II: Install your new RCS 2.0S Software

Step III:

Reprogramming the

RCS 2.0S Firmware

Update the RCS 2.0S Firmware

Your RCS 2.0S has been pre-programmed with the latest firmware when shipped from our factory and does not need to be updated with the program CD that came with your unit. TacT Audio may occasionally release updated versions of the RCS software that will be available on our website “www.tactaudio.com”. This new software may contain updates or enhancements for your RCS 2.0S. When instructed by a technician or messaged from our website please follow the instruction below to update your RCS 2.0S firmware.

First un-install the current version of the RCS 2.0S correction software on your computer.

1 - Turn on your computer.

2 - Open the Windows control panel and select the “Add/Remove Programs” option.

3- Highlight the “TacT-2.0S” option and click on “Change/Remove”.

4- Select “Yes” and the old Tact 2.0S software will be removed.

NOTE:Your target curves and measurements stored under unique names will NOT be removed.

You now need to install the new TacT 2.0S RCS software on your computer.

-Double-click on the “Tact 2.0S vx.x.exe” file that you have downloaded or is found on the root of your CD and follow the installation instructions.

Program the new firmware for the RCS 2.0S.

1 - Connect the PC to the RCS 2.0S using the RS232 cable. Please refer to the RCS 2.0S RS232 section of the user’s manual or the RS232 Connection document for help.

CAUTION: There should only be one RCS 2.0S connected to the RS232 cable during system reprogramming. Please disconnect any other RCS 2.0S units that may be daisy chained to the RCS 2.0S that is being programmed.

2 - Start the RCS 2.0S correction software on your computer

3 - Use the “Communication” option in the Tact 2.0S room correction software to make sure that the RCS 2.0S and your computer are communicating. Please refer to the RCS 2.0S RS232 section of the user’s manual or the RS232 Connection document for help.

4 - Turn the RCS 2.0S OFF from the rear panel mains switch.

Tact Audio 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents RCS 2.0S Blank Tact Audio Page Registration AcknowledgmentsTable of contents Unpacking the RCS 2.0S Accessories Operating voltageIntroduction Digital input Digital Output RCS 2.0S ConnectionsDigital Input Section Digital Output Section Tact AudioAnalog Input RCS 2.0S Connections Optional ModulesOptional DAC module Analog OutputAnalog Output Section Microphone input Microphone Input Tact AudioRCS 2.0S Connections RS-232 interface Tact Audio AC mains input & mains switchPorts RS-232 Interface Ports AC mains inputFront Panel Controls Standby Input selectorMenu Remote Control Correction block Volume BlockEQ preset selection Correction preset selectionInput sampling frequency indicator Front Panel DisplaySettings Delay menuSaving Menu Right for each room correction preset including bypass UP and Down buttons to change its valueAssigned to each input independently Test menu Displ menuAnd/or daisy chain RS232 ports to link multiple components Selection before the AMP setting will be enabledAddr menu REM menuPreset Link N Link Y EQ L Parametric EQ LEV OCTFront Panel Display Tone menu Frequency and OctaveTer Tact Audio Info menu OFS menuYour computer system must meet the following requirements TacT 2.0S Room Correction SoftwareRCS-2.0 S to your Connect yourComputer Connection at this timeTact Audio Blank Before You Begin Quick SetupStep Quick Setup Getting StartedQuick Setup Automation Update the RCS 2.0S Firmware Tact-2.0 S Programing Mode Update the RCS 2.0S Firmware Restoring the Default Update the RCS 2.0S Firmware StepRCS 2.0S Settings Default Settings windowBlank Tact Audio TacT Audio, Inc
Top Page Image Contents