Front Panel Display |
|
|
|
|
|
|
|
|
|
|
|
|
| |
| OUT menu | The output menu is used to set the RCS 2.0S to either a Stereo or Mono output | ||||||||||||
|
| mode. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| Out Menu : | 3 |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| Output Mode:Stereo |
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| STEREO |
| MONO |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| 1 | 2 |
|
|
|
| ||||||
|
| 1 | - STEREO mode produces 2 output signals. This is standard two |
| ||||||||||
|
|
| channel stereo mode. |
|
|
|
|
|
|
|
| |||
|
| 2 | - Mono mode will output the same signal on both the Left and Right |
| ||||||||||
|
|
| channels. |
|
|
|
|
|
|
|
| |||
|
| 3 | - Active OUT setting. |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use the “LEFT” and “RIGHT” buttons to highlight the desired option and select it by pressing the “ENTER” button.
AMP menu | The AMP menu is designed to allow the RCS 2.0S to interface with the TacT | |||||
| M2150 and S2150 digital amplifiers. With the RCS 2.0S you can control multiple | |||||
| digital amplifiers for a biamplified setup. This setting should only be ENABLED if | |||||
| you have a Tact digital amplifier attached to the RCS 2.0S. | |||||
|
|
|
|
|
|
|
| Amp Menu : | |||||
|
|
|
| |||
|
|
|
|
|
| |
|
|
| ENABLED |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 |
|
| |||
|
| 1 - Active AMP settings. | ||||
|
|
|
|
|
|
|
| To change the settings press the “ENTER” button. You will have to confirm your | |||||
| selection before the AMP setting will be enabled. | |||||
| NOTE: When a TacT digital amplifier is controlled by the RCS 2.0S, all of | |||||
| the amplifiers front panel and IR controls are disabled. Use the RS232 port | |||||
| and/or daisy chain RS232 ports to link multiple components. | |||||
| CAUTION:The AMP setting should only be set to ENABLED if you have Tact | |||||
| amplifiers connected to the RCS 2.0S. WHEN THE AMP OPTION IS SET TO | |||||
| ENABLED BOTH THE ANALOG AND DIGITAL OUTPUT WITH WILL OUTPUT A | |||||
| FULL LEVEL SIGNAL REGARDLESS OF THE RCS 2.0S MASTER VOLUME | |||||
| SETTING. If you do not have Tact amplifiers connected to your system you | |||||
| will not be able to control the output level from the RCS 2.0S volume control. | |||||
| The output is sent at its maximum level and can result in damage to your | |||||
| speakers. | |||||