Polaroid 215EPolaview manual Canceling, Enlarging scanning, Line conversion, Function, Changing to

Page 38

 

Getting started

Canceling the

When a VIDEO/S-VIDEO signal in NTSC format or a signal with less than

enlarging (scanning

800 x 600 dots (for example, 640x480 dots) is input, the LCD projector

line conversion)

automatically enlarges the image to 800 x 600 dots. This may cause picture quality

function

degradation. For a better image, select EXPANSION (VGA) or (NTSC):OFF by

 

the following procedure.

 

The procedure and on-screen displays shown below assume that an RGB signal is

 

being used as the input signal.

 

MENU

 

SET UP PROJECTOR

 

RGB ADJUST

FRONT/REAR

FRONT

RGB SYNC MENU

INPUT DISP

ON

>SET UP PROJECTOR

 

REMOTE POWER

ON

LANGUAGE

 

>EXPANSION (VGA)

ON

 

/SPRACHE /LANGUE

LAMP TIME RESET

NO

 

/IDIOMA /LINGUA

 

 

 

 

 

SELECT : PUSH ZorX

SELECT : PUSH ZorX

SET

: PUSH CorV

SET

: PUSH CorV

END

: PUSH MENU

END

: PUSH MENU

 

 

1.Press MENU to display the menu.

2.Press Z or X to select SET UP PROJECTOR, and then press C or V to display the screen.

3.Press Z or X to select EXPANSION (VGA) OR (NTSC), and then press C or V to select ON or OFF.

Select OFF to cancel the enlarging (scanning line conversion) function.

Select ON to use the enlarging (scanning line conversion) function. (This is the factory setting.)

4.Press MENU twice to exit.

Changing to 16:9

When a VIDEO or S-VIDEO signal in NTSC format is input, the image can be

(wide) screen format

displayed in 16:9 (wide) screen format by the following procedure.

 

S-VIDEO/VIDEO input is selected (page 34).

 

MENU

 

SET UP PROJECTOR

 

RGB ADJUST

FRONT/REAR

FRONT

RGB SYNC MENU

INPUT DISP

ON

>SET UP PROJECTOR

 

REMOTE POWER

ON

LANGUAGE

 

>16:9 (NTSC)

OFF

 

/SPRACHE /LANGUE

EXPANSION (NTSC)

NO

 

/IDIOMA /LINGUA

LAMP TIME RESET

NO

SELECT : PUSH ZorX

SELECT : PUSH ZorX

SET

: PUSH CorV

SET

: PUSH CorV

END

: PUSH MENU

END

: PUSH MENU

 

 

1.Press MENU to display the menu.

2.Press Z or X to select SET UP PROJECTOR, and then press C or V to display the screen.

3.Press Z or X to select 16:9 (NTSC), and then press C or V to select ON or OFF.

Select OFF to return the normal screen. (This is the factory setting.) Select ON to display in 16:9 (wide) screen format.

4.Press MENU twice to exit.

Note: Even if the 16:9 (wide) screen feature is set to OFF, when an “S1” signal is input, the image is automatically displayed in 16:9 (wide) screen mode.

English 37

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Polaview215E Table of contents Polview 215E LCD Projector User’s Guide Appendix Polview 215E LCD Projector User’s Guide General information Declaration of Conformity Important safeguards General information General information LCD projector features IntroductionVideo board Contents of the LCD projector box Parts list and accessories Remote control unitBefore using the remote control LCD projector LCD projector back Bottom How to use the remote control unit Click 2 button Pointer button Mouse button Click 1 buttonSetting up the LCD projector Adjusting the lens Computer RGB signal Connecting the LCD projectorConnecting to a Chart. seeVCR Computer cables & adapters Pin assignments VGASetting the DIP SwitchesRS-232C connector Mini DIN 8-pin RS-232C connector D-Sub25-pinFactory preset timing Vertical frequency 85.080 Hz 72.8088 Hz 75.0000 Hz Vertical frequency 72.188 Hz 75.000 Hz 85.061 Hz Preset timing *Compression Turning the power on and off PowerSet the Main power switch on the LCD projector to OFF Positioning the LCD projector and screenLCD projector/screen relative position Turn on the power Basic LCD projector operationInput signal Input signal format Using other useful functions Disabling the Power button on the remote control unit Input Disp SET UP ProjectorLine conversion CancelingEnlarging scanning FunctionMinutes before Power is shut off Input image Adjusting the projected imageAdjustment Recall standard Adjustments for input imageSettings RGB sync adjustment Posi Vertical Position Control Adjustments for RGB inputPhase Control Posi Horizontal Position ControlPC Output Timing Relative Value Chart Adjusting the white balance Memory Projecting PC-Card ATA Flash Card data Repeat Play When usingPress C or V to select an image Type in A\SETUP.EXE and click OK Jpeg Viewer featuresJpeg Viewer installation Turn on the PC and start up Insert the PC-Card ATA Flash Card not supplied intoFollowing are the software’s menu items and their functions Select the PC-Card drive for saving images file name numbers are renewed automatically Select the image that you want to delete ProMouse Control Feature Windows 95 / WindowsProMouse installation Using the ProMouse Software How to program Macintosh Easy InstallCustom Install Turn on the MacintoshSelect the Option Connection Setting Select the Printer port or Modem port. Then click OKApple Menu How to program Maintenance AppendixSet the Main power switch to OFF and unplug the power cord Place the LCD projector up on its side as illustratedReplace the air filter unit Clean the filterRemove the air filter unit Replace the lamp Order Lamp 630146 Tools required a coin Replace the lamp unit screws Install the new lamp unitRemove the lamp unit screw Lamp Time Reset Before Requesting Service Specifications FCC, UL, C-UL, CE, VDE Polaroid Three Year Limited Warranty Polaroid Offices and Service Centers Norge
Top Page Image Contents