Polaroid 215EPolaview manual Disabling the Power button on the remote control unit

Page 37

Getting started

Turning off the input The function which displays the currently selected input signal on the screen can be

signal display turned off by the following procedure. The procedure and on-screen displays shown below assume that an RGB signal is being used as the input signal.


	MENU			SET UP PROJECTOR
RGB ADJUST			FRONT/REAR			FRONT
RGB SYNC MENU			>INPUT DISP			ON
>SET UP PROJECTOR			REMOTE POWER			ON
LANGUAGE			EXPANSION (VGA)			ON
	/SPRACHE /LANGUE		LAMP TIME RESET			NO
	/IDIOMA /LINGUA
SELECT : PUSH ZorX			SELECT : PUSH ZorX
SET	: PUSH CorV		SET		: PUSH CorV
END	: PUSH MENU		END		: PUSH MENU

1.Press MENU to display the menu.

2.Press Z or X to select SET UP PROJECTOR, and then press C or V to display the screen.

Disabling the POWER button on the remote control unit

3.Press Z or X to select INPUT DISP, and then press C or V to select ON or OFF.

Select OFF to turn off the input signal display function.

Select ON to turn on the input signal display function. The input signal will be displayed each time it is changed. (This is the factory setting.)

4.Press MENU twice to exit.

In order to prevent the power from being turned off by mistake, the POWER button on the remote control unit can be disabled by the following procedure. The procedure and on-screen displays shown below assume that an RGB signal is being used as the input signal.


	MENU			SET UP PROJECTOR
RGB ADJUST			FRONT/REAR			FRONT
RGB SYNC MENU			INPUT DISP			ON
>SET UP PROJECTOR			>REMOTE POWER			ON
LANGUAGE			EXPANSION (VGA)			ON
	/SPRACHE /LANGUE		LAMP TIME RESET			NO
	/IDIOMA /LINGUA
SELECT : PUSH ZorX			SELECT : PUSH ZorX
SET	: PUSH CorV		SET		: PUSH CorV
END	: PUSH MENU		END		: PUSH MENU

1.Press MENU to display the menu.

2.Press Z or X to select SET UP PROJECTOR, and then press C or V to display the screen.

3.Press Z or X to select REMOTE POWER, and then press C or V to select ON or OFF.

Select OFF to disable the POWER button on the remote control unit.

Select ON to use the POWER button on the remote control unit normally. (This is the factory setting.)

4.Press MENU twice to exit.

36Polaview 215E LCD Projector User’s Guide

Image 37

Contents Polaview215E Table of contents Polview 215E LCD Projector User’s Guide Appendix Polview 215E LCD Projector User’s Guide General information Declaration of Conformity Important safeguards General information General information Introduction LCD projector featuresVideo board Contents of the LCD projector box Remote control unit Parts list and accessoriesBefore using the remote control LCD projector LCD projector back Bottom Click 2 button Pointer button Mouse button Click 1 button How to use the remote control unitSetting up the LCD projector Adjusting the lens Connecting to a Connecting the LCD projectorComputer RGB signal Chart. seeVCR Computer cables & adapters VGA Pin assignmentsSwitches Setting the DIPRS-232C connector D-Sub25-pin RS-232C connector Mini DIN 8-pinFactory preset timing Vertical frequency 85.080 Hz 72.8088 Hz 75.0000 Hz Vertical frequency 72.188 Hz 75.000 Hz 85.061 Hz Preset timing *Compression Power Turning the power on and offPositioning the LCD projector and screen Set the Main power switch on the LCD projector to OFFLCD projector/screen relative position Basic LCD projector operation Turn on the powerInput signal Input signal format Using other useful functions Input Disp SET UP Projector Disabling the Power button on the remote control unitEnlarging scanning CancelingLine conversion FunctionMinutes before Power is shut off Adjustment Adjusting the projected imageInput image Settings Adjustments for input imageRecall standard RGB sync adjustment Phase Control Adjustments for RGB inputPosi Vertical Position Control Posi Horizontal Position ControlPC Output Timing Relative Value Chart Adjusting the white balance Memory Projecting PC-Card ATA Flash Card data Press C or V to select an image When usingRepeat Play Jpeg Viewer installation Jpeg Viewer featuresType in A\SETUP.EXE and click OK Insert the PC-Card ATA Flash Card not supplied into Turn on the PC and start upFollowing are the software’s menu items and their functions Select the PC-Card drive for saving images ﬁle name numbers are renewed automatically Select the image that you want to delete Windows 95 / Windows ProMouse Control FeatureProMouse installation Using the ProMouse Software How to program Custom Install Easy InstallMacintosh Turn on the MacintoshSelect the Printer port or Modem port. Then click OK Select the Option Connection SettingApple Menu How to program Appendix MaintenancePlace the LCD projector up on its side as illustrated Set the Main power switch to OFF and unplug the power cordRemove the air filter unit Clean the filterReplace the air filter unit Replace the lamp Order Lamp 630146 Tools required a coin Remove the lamp unit screw Install the new lamp unitReplace the lamp unit screws Lamp Time Reset Before Requesting Service Specifications FCC, UL, C-UL, CE, VDE Polaroid Three Year Limited Warranty Polaroid Offices and Service Centers Norge