Polaroid 215EPolaview manual Connecting the LCD projector, Connecting to a, Computer RGB signal

Page 21

Getting started

Connecting the LCD projector

Before you begin

Turn off the power supply of each system component before connecting any of the components.

If necessary cables for connecting any of the system components are not supplied with the component or available as an optional accessory, you may need to obtain them yourself.

Connecting to a

Diagram numbers correspond to the numbers in the computer cables & adapters

computer (RGB signal)

chart. (see page 22).

 

Computer

Audio system

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

f

Computer monitor cable

 

 

 

 

 

 

Audio cable

(not included)

 

 

(not included)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

e

S-VIDEO VIDEO IN L-AUDIO IN-R

RS232C RGB IN AUDIO IN RGB OIUT AUDIO OUT

 

Connector

a

jacks on

left side of

 

computer

b c d

a RS-232C 25-pin adapter (6)

d PC audio cable (3)

b RS-232C cable (4)

e RS-232C 9-pin adapter (5)

c VGA cable (1)

f VGA Mac adapter (2)

Note:

The RGB input accepts signals from VGA, SVGA, XGA (Compression), and MAC compatible computers without the need for any additional hardware.

Plug the VGA signal cable (supplied) correctly into the RGB IN terminal on the LCD projector and the RGB signal output terminal on your computer. Secure the plugs by tightening the thumb screws.

When connecting the LCD projector to a Macintosh series computer, first connect the VGA/MAC adapter (supplied) to the RGB signal input terminal on your computer. Then, firmly plug the VGA signal cable into both the RGB IN terminal on the LCD projector and the VGA/MAC adapter on the computer. Secure the plugs by tightening the thumb screws.

To view images simultaneously on the monitor and projection screen, connect your computer monitor to the LCD projector’s RGB OUT terminal.

When the LCD projector is connected to external devices (for example, a personal computer) you can use the remote control unit in place of the computer’s mouse by attaching the RS-232C connector cable.

20Polaview 215E LCD Projector User’s Guide

Image 21
Contents Polaview215E Table of contents Polview 215E LCD Projector User’s Guide Appendix Polview 215E LCD Projector User’s Guide General information Declaration of Conformity Important safeguards General information General information Introduction LCD projector featuresVideo board Contents of the LCD projector box Remote control unit Parts list and accessoriesBefore using the remote control LCD projector LCD projector back Bottom Click 2 button Pointer button Mouse button Click 1 button How to use the remote control unitSetting up the LCD projector Adjusting the lens Connecting to a Connecting the LCD projectorComputer RGB signal Chart. seeVCR Computer cables & adapters VGA Pin assignmentsSwitches Setting the DIPRS-232C connector D-Sub25-pin RS-232C connector Mini DIN 8-pinFactory preset timing Vertical frequency 85.080 Hz 72.8088 Hz 75.0000 Hz Vertical frequency 72.188 Hz 75.000 Hz 85.061 Hz Preset timing *Compression Power Turning the power on and offPositioning the LCD projector and screen Set the Main power switch on the LCD projector to OFFLCD projector/screen relative position Basic LCD projector operation Turn on the powerInput signal Input signal format Using other useful functions Input Disp SET UP Projector Disabling the Power button on the remote control unitEnlarging scanning CancelingLine conversion FunctionMinutes before Power is shut off Adjusting the projected image AdjustmentInput image Adjustments for input image SettingsRecall standard RGB sync adjustment Phase Control Adjustments for RGB inputPosi Vertical Position Control Posi Horizontal Position ControlPC Output Timing Relative Value Chart Adjusting the white balance Memory Projecting PC-Card ATA Flash Card data When using Press C or V to select an imageRepeat Play Jpeg Viewer features Jpeg Viewer installationType in A\SETUP.EXE and click OK Insert the PC-Card ATA Flash Card not supplied into Turn on the PC and start upFollowing are the software’s menu items and their functions Select the PC-Card drive for saving images file name numbers are renewed automatically Select the image that you want to delete Windows 95 / Windows ProMouse Control FeatureProMouse installation Using the ProMouse Software How to program Custom Install Easy InstallMacintosh Turn on the MacintoshSelect the Printer port or Modem port. Then click OK Select the Option Connection SettingApple Menu How to program Appendix MaintenancePlace the LCD projector up on its side as illustrated Set the Main power switch to OFF and unplug the power cordClean the filter Remove the air filter unitReplace the air filter unit Replace the lamp Order Lamp 630146 Tools required a coin Install the new lamp unit Remove the lamp unit screwReplace the lamp unit screws Lamp Time Reset Before Requesting Service Specifications FCC, UL, C-UL, CE, VDE Polaroid Three Year Limited Warranty Polaroid Offices and Service Centers Norge