BenQ W7000+ user manual Projection dimensions, Installation for a 169 ratio screen

Page 14

If you place the projector in a different position (to that recommended), you will have to tilt it down or up to center the image on the screen. In these situations, some image distortion will occur. Use the Keystone function to correct the distortion. See "Correcting picture distortion" on page 25 for details.

Projection dimensions

Installation for a 16:9 ratio screen

Floor Installation
<A>	<B>	<F>
		<F>
		<G>
	<E>
	<C>	<D>
		<D>

<F>: Screen

<G>: Center of lens

Ceiling Installation

		<D>
<A>	<E>
<A>	<B>
	<B>
		<G>
		<F>
<C>
<F>: Screen		<G>: Center of lens

The screen aspect ratio is 16:9 and the projected picture is 16:9

	Screen dimensions			Projection distance <D> [mm]
Diagonal		Height	Width	Min distance		Max distance	Lowest/Highest
<A>		Height	Width	Min distance		Max distance	lens position
<A>		<B>	<C>	(with max	Average	(with min	lens position
[inch		<B>	<C>	(with max	Average	(with min	<E> [mm]
[inch		[mm]	[mm]	zoom)		zoom)	<E> [mm]
(mm)]		[mm]	[mm]	zoom)		zoom)
(mm)]

30	(762)	374	664	1077	1346	1616	47

40	(1016)	498	885	1436	1795	2154	62

50	(1270)	623	1107	1795	2244	2693	78

60	(1524)	747	1328	2154	2693	3232	93

70	(1778)	872	1549	2513	3142	3770	109

80	(2032)	996	1771	2873	3591	4309	125

90	(2286)	1121	1992	3232	4039	4847	140

100	(2540)	1245	2214	3591	4488	5386	156

110	(2794)	1370	2435	3950	4937	5925	171

120	(3048)	1494	2656	4309	5386	6463	187

130	(3302)	1619	2878	4668	5835	7002	202

140	(3556)	1743	3099	5027	6284	7540	218

150	(3810)	1868	3320	5386	6732	8079	233

160	(4064)	1992	3542	5745	7181	8618	249

170	(4318)	2117	3763	6104	7630	9156	265

180	(4572)	2241	3984	6463	8079	9695	280

190	(4826)	2366	4206	6822	8528	10233	296

200	(5080)	2490	4427	7181	8977	10772	311

250	(6350)	3113	5534	8977	11221	13465	389

300	(7620)	3735	6641	10772	13465	16158	467

The above numbers are approximate and may be slightly different from the actual measurements. Only the recommended screen sizes are listed. If your screen size is not in the table above, please contact your dealer for assistance.

14 Positioning your projector

Image 14

Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewRemote control reaching the projector Remote control batteriesRemote control operation Ceiling mounting the projectorProjector features Rear view Projector exterior viewFront and upper side view Under viewFocus ring Controls and functionsControl panel Remote control Front Table Positioning your projectorChoosing a location Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D Lowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen aspect ratio is 43 and the projected picture isShifting the projection lens To use the lens shift leverPreparations Connecting with video equipmentConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cablePreparations Using the projectorTurning the projector on Using the OSD menu Fine-tuning the image size and clarityUsing the remote control or projector Selecting an input sourceUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Ii. See step iii below for further operationFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Fine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To adjust and store the settings Color ManagementSelecting the aspect ratio Setting Film ModeSetting 3D Comb Filter About the aspect ratioUsing Panamorph lenses optional Aspect ratio Aspect ratio imageTo activate High Altitude Mode Operating in a high altitude environmentMain Source or PIP Source and press ENTER. The source To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Using the 3D menus Watching 3D contentConnecting 3D video devices Personalizing the projector menu displayTo lock the keys Locking control keysTurning the projector off Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information System SetupAdvanced Setup Function Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menuInformation menu Additional information Care of the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Connecting with video equipment Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionYour Blu-ray Disc is not in 3D TroubleshootingProblem Cause Remedy FormatOptical SpecificationsGeneral characteristics ElectricalDimensions 317 145 428Refresh rate Frequency Pixel Format Timing chartSupported timing for PC input KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty Disclaimer