BenQ W7000+ user manual Using the projector, Turning the projector on, Preparations

Page 20

Using the projector

Preparations

1. Plug in and turn all of the connected equipment on.

2. If not already in, plug the supplied power cable into the AC inlet on the rear of the projector.

3. Plug the power cable into a wall power outlet and turn the wall switch on.

Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire.

Turning the projector on

Follow the steps below.

1. Make sure the Power light is orange after power has been applied.

2. Press and hold POWER ON ( II ) on the projector or remote control to turn the projector on.

3. The fans will start operating, and a start-upimage displays on the screen for a few seconds while it warms up.

The projector will not respond to further commands while it is warming up.

4.If you are prompted for a password, press the arrow keys to enter a six-digit password. See "Utilizing the password function" on page 23 for details.

5."Source Searching..." will be displayed on the screen before the projector identifies the input source. This message will remain on the screen until a valid signal is detected. See "Selecting an input source" on page 21 for details.

6.If the horizontal frequency of the input source exceeds the range of the projector, the message "No Signal" will be displayed on the screen. This message will remain on-screen until you change the input source to an appropriate one.

20 Connecting with video equipment

Image 20

Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewRemote control batteries Remote control operationRemote control reaching the projector Ceiling mounting the projectorProjector features Projector exterior view Front and upper side viewRear view Under viewFocus ring Controls and functionsControl panel Remote control Front Table Positioning your projectorChoosing a location Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isShifting the projection lens To use the lens shift leverPreparations Connecting with video equipmentConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cablePreparations Using the projectorTurning the projector on Fine-tuning the image size and clarity Using the remote control or projectorUsing the OSD menu Selecting an input sourceUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorIf you forget the password Utilizing the password functionSetting a password Entering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Ii. See step iii below for further operationFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Fine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To adjust and store the settings Color ManagementSetting Film Mode Setting 3D Comb FilterSelecting the aspect ratio About the aspect ratioUsing Panamorph lenses optional Aspect ratio Aspect ratio imageTo activate High Altitude Mode Operating in a high altitude environmentMain Source or PIP Source and press ENTER. The source To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu displayTo lock the keys Locking control keysTurning the projector off Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information System SetupAdvanced Setup Function Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menuInformation menu Additional information Care of the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Connecting with video equipment Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications General characteristicsOptical ElectricalDimensions 317 145 428Timing chart Supported timing for PC inputRefresh rate Frequency Pixel Format KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty and Copyright information WarrantyCopyright Disclaimer