BenQ W7000+ Operating in a high altitude environment, To activate High Altitude Mode

Page 34

Operating in a high altitude environment

We recommend that you activate High Altitude Mode when your environment is higher than 1500 meters (around 4920 feet) above sea level, or whenever the projector will be used for extended periods of time (>10 hours) without shutdown.

To activate High Altitude Mode:

1.Press MENU and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight High Altitude Mode.

3.Press / to select On. A confirmation message displays.

4.Highlight Yes and press ENTER.

Operation under High Altitude Mode may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to High Altitude Mode to solve these symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Advanced Setup

Lamp Settings
HDMI Settings
Baud Rate	115200
Test Pattern
High Altitude Mode	Off
Password
Key Lock	Off
Reset All Settings
ISF
S-Video	Back
WARNING

We recommend you use the High Altitude Mode by selecting it whenever your environment is higher than 1500m.

Do you want to turn the High Altitude

Mode ON?

Yes No

34 Connecting with video equipment

Image 34

Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control reaching the projector Remote control batteriesRemote control operation Ceiling mounting the projectorProjector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Controls and functionsFocus ring Remote control Choosing a location Positioning your projectorFront Table Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D Lowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen aspect ratio is 43 and the projected picture isShifting the projection lens To use the lens shift leverConnecting Hdmi devices Connecting with video equipmentPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on Using the projectorPreparations Using the OSD menu Fine-tuning the image size and clarityUsing the remote control or projector Selecting an input sourceUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorSetting a password Utilizing the password functionIf you forget the password Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Ii. See step iii below for further operationSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Resetting the picture mode Setting the User 1/User 2/User 3 modeTo reset the picture mode to the preset factory values Fine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To adjust and store the settings Color ManagementSelecting the aspect ratio Setting Film ModeSetting 3D Comb Filter About the aspect ratioUsing Panamorph lenses optional Aspect ratio Aspect ratio imageTo activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP window Using the remote controlMain Source or PIP Source and press ENTER. The source Using the 3D menus Watching 3D contentConnecting 3D video devices Personalizing the projector menu displayTurning the projector off Locking control keysTo lock the keys On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Advanced Setup System SetupInformation Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menu Advanced Setup menuInformation menu Additional information Care of the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Connecting with video equipment Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionYour Blu-ray Disc is not in 3D TroubleshootingProblem Cause Remedy FormatOptical SpecificationsGeneral characteristics ElectricalDimensions 317 145 428Refresh rate Frequency Pixel Format Timing chartSupported timing for PC input KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty Disclaimer