BenQ W7000+ user manual Shifting the projection lens, To use the lens shift lever

Page 16

Shifting the projection lens

The lens shift control provides flexibility for installing your projector. It allows the projector to be positioned off the center of the screen.

The lens shift is expressed as a percentage of the projected image height or width. It is measured as an offset from the projected image’s vertical or horizontal center. You can use the lever to shift the projection lens in any direction within the allowable range depending on your desired image position.

To use the lens shift lever:

1.Release the lever by turning it counterclockwise.

2.Move the lever to adjust the projected image position.

3.Lock the lever by turning it clockwise.

• When the screen position is fixed
Projector
	Range of
Screen	placement
	Center of lens
• When the projector position is fixed
100%
25%
-25%
-100%
41.3%	41.3%

• Please do not over-tighten the lever.

•Lens shift adjustment will not result in a degraded picture quality. In the unlikely event that the image distortion is produced, see "Adjusting the projected image" on page 25 for details.

16 Positioning your projector

Image 16

Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control batteries Remote control operationRemote control reaching the projector Ceiling mounting the projectorProjector features Projector exterior view Front and upper side viewRear view Under viewControl panel Controls and functionsFocus ring Remote control Choosing a location Positioning your projectorFront Table Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isShifting the projection lens To use the lens shift leverConnecting Hdmi devices Connecting with video equipmentPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on Using the projectorPreparations Fine-tuning the image size and clarity Using the remote control or projectorUsing the OSD menu Selecting an input sourceUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Ii. See step iii below for further operationSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Resetting the picture mode Setting the User 1/User 2/User 3 modeTo reset the picture mode to the preset factory values Fine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To adjust and store the settings Color ManagementSetting Film Mode Setting 3D Comb FilterSelecting the aspect ratio About the aspect ratioUsing Panamorph lenses optional Aspect ratio Aspect ratio imageTo activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP window Using the remote controlMain Source or PIP Source and press ENTER. The source Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu displayTurning the projector off Locking control keysTo lock the keys On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Advanced Setup System SetupInformation Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menu Advanced Setup menuInformation menu Additional information Care of the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Connecting with video equipment Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications General characteristicsOptical ElectricalDimensions 317 145 428Timing chart Supported timing for PC inputRefresh rate Frequency Pixel Format KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty and Copyright information WarrantyCopyright Disclaimer