BenQ W7000+ user manual Warranty and Copyright information, Disclaimer

Page 58

Warranty and Copyright information

Warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ’s written instructions, especially the ambient humidity must be in-between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 3000 meters, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright

Copyright © 2011 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

All trademarks and registered trademarks are the property of their respective owners.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ Corporation to notify any person of such revision or changes.

58 Connecting with video equipment

Image 58
Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control reaching the projector Remote control batteriesRemote control operation Ceiling mounting the projectorProjector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Controls and functionsFocus ring Remote control Choosing a location Positioning your projectorFront Table Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D Lowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen aspect ratio is 43 and the projected picture isShifting the projection lens To use the lens shift leverConnecting Hdmi devices Connecting with video equipmentPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableTurning the projector on Using the projectorPreparations Using the OSD menu Fine-tuning the image size and clarityUsing the remote control or projector Selecting an input sourceUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorSetting a password Utilizing the password functionIf you forget the password Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Ii. See step iii below for further operationSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Resetting the picture mode Setting the User 1/User 2/User 3 modeTo reset the picture mode to the preset factory values Fine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To adjust and store the settings Color ManagementSelecting the aspect ratio Setting Film ModeSetting 3D Comb Filter About the aspect ratioUsing Panamorph lenses optional Aspect ratio Aspect ratio imageTo activate High Altitude Mode Operating in a high altitude environmentDisplaying more than one image source simultaneously To display the PIP window Using the remote controlMain Source or PIP Source and press ENTER. The source Using the 3D menus Watching 3D contentConnecting 3D video devices Personalizing the projector menu displayTurning the projector off Locking control keysTo lock the keys On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Advanced Setup System SetupInformation Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menu Advanced Setup menuInformation menu Additional information Care of the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Connecting with video equipment Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionYour Blu-ray Disc is not in 3D TroubleshootingProblem Cause Remedy FormatOptical SpecificationsGeneral characteristics ElectricalDimensions 317 145 428Refresh rate Frequency Pixel Format Timing chartSupported timing for PC input KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty Disclaimer