BenQ W7000+ Selecting an input source, Fine-tuning the image size and clarity, Using the OSD menu

Page 21

Selecting an input source

The projector can be connected to multiple equipment at the same time. When the projector is first turned on, it will attempt to reconnect with the input source which was in use when the projector was last shut down.

To select the video source:

Using the remote control or projector

Press one of the Source keys on the remote control, or press SOURCE on the projector repeatedly until your desired signal is selected.

Using the OSD menu

1.Press MENU and then press / until the System Setup menu is highlighted.

2.Press to highlight Input Source and press ENTER. The source selection bar displays.

3.Press / repeatedly until your desired signal is selected and press

ENTER.

Once detected, the selected source information will display on the screen for seconds. If there are multiple pieces of equipment connected to the projector, you can go back to the source selection bar again to search for other signals.

If you want the projector to automatically search for the signals, select On in the System Setup > Auto Source Search menu.

If you want to use the PIP function, see "Displaying more than one image source simultaneously" on page 35 for details.

System Setup

Language

English

Splash Screen

BenQ

Projector Position

Front Table

Auto Off

Disable

Sleep Timer

Disable

Menu Settings

 

Input Source

ENTER

Auto Source Search

On

S-Video

Back

HDMI 1

NOTE: When

 

automatically

HDMI 2

searching for a

Video

valid input source,

the projector

 

S-Video

cycles through

Component 1

the available

signals following

 

Component 2

the sequence

 

from top to

PC

bottom as the

 

source selection

 

bar shows.

Fine-tuning the image size and clarity

1.Adjust the projected picture to the size that you need using the zoom ring.

2.Sharpen the picture by rotating the focus ring.

Connecting with video equipment

21

Image 21
Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contentsRemote control operation Remote control batteriesRemote control reaching the projector Ceiling mounting the projectorProjector features Front and upper side view Projector exterior viewRear view Under viewControls and functions Control panelFocus ring Remote control Positioning your projector Choosing a locationFront Table Determine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsFloor Installation Ceiling Installation Installation for a 43 ratio screenScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isTo use the lens shift lever Shifting the projection lensConnecting with video equipment Connecting Hdmi devicesPreparations Connecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerUsing the projector Turning the projector onPreparations Using the remote control or projector Fine-tuning the image size and clarityUsing the OSD menu Selecting an input sourceUsing a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Ii. See step iii below for further operationUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 mode Resetting the picture modeTo reset the picture mode to the preset factory values Fine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color Color Management To adjust and store the settingsSetting 3D Comb Filter Setting Film ModeSelecting the aspect ratio About the aspect ratioAspect ratio Aspect ratio image Using Panamorph lenses optionalOperating in a high altitude environment To activate High Altitude ModeTo display the PIP window Using the remote control Displaying more than one image source simultaneouslyMain Source or PIP Source and press ENTER. The source Connecting 3D video devices Watching 3D contentUsing the 3D menus Personalizing the projector menu displayLocking control keys Turning the projector offTo lock the keys On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup Advanced SetupInformation Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu Advanced Setup menu System Setup menuInformation menu Care of the projector Additional informationSetting Auto Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Connecting with video equipment Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsProblem Cause Remedy TroubleshootingYour Blu-ray Disc is not in 3D FormatGeneral characteristics SpecificationsOptical Electrical317 145 428 DimensionsSupported timing for PC input Timing chartRefresh rate Frequency Pixel Format KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Format Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty Warranty and Copyright informationCopyright Disclaimer