BenQ W7000+ user manual Using the preset and user modes, Selecting a preset mode

Page 26

Using the preset and user modes

Selecting a preset mode

The projector is preset with several pre-defined picture modes so that you can choose one to suit your operating environment and input source picture type.

To select a picture mode that suits your need:

•Using the remote control

1.Press PRESET MODE repeatedly or USER 1, USER 2/ISF NIGHT, USER 3/ISF DAY, DEFAULT on the remote control, or PRESET MODE on the projector repeatedly until your desired mode is selected.

•Using the OSD menu

1.Press MENU and then press / until the Picture -- Basic menu is highlighted.

2.Press to highlight Preset Mode.

3.Press / until your desired mode is selected.

These modes consist of preset values suitable for various projection situations as described below:

Picture -- Basic

Preset Mode

Cinema

Load Settings From

 

Brightness

50

Contrast

50

Color

50

Tint

0

Sharpness

3

Flesh Tone

3

Reset Picture Settings

 

S-Video

Back

•Cinema: With well-balanced color saturation and contrast with a

low brightness level, this is most suitable for enjoying movies in a totally dark environment (as you would find in a commercial cinema).

•Dynamic: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

•Standard: It is slightly brighter than Cinema mode, and suitable for use in rooms where there is a small amount of ambient light.

•User 1/User 2/User 3: Recalls the customized settings. See "Setting the User 1/User 2/User 3 mode" on page 27 for details.

Fine-tuning the selected picture mode

The pre-defined picture mode settings can be altered via the available items shown in the Picture -- Basic and Picture -- Advanced menus.

To fine-tune the picture mode:

1.Press MENU and then press / until the Picture -- Basic or Picture -- Advanced menu is highlighted.

2.Press to highlight the item you want to adjust and press / to set your desired value. Your selection is automatically stored in the projector and associated with that input source.

See "Fine-tuning the picture quality" on page 28 and "Advanced picture quality controls" on page 29 for details.

Each time you change the picture mode, the projector also changes the setting to the one which was last set for that particular picture mode on that particular input. If you change the input source, the most recently used picture mode and settings for that input and resolution will be restored.

26 Connecting with video equipment

Page 25 Page 27
Image 26
Page 25 Page 27
Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewRemote control reaching the projector Remote control batteriesRemote control operation Ceiling mounting the projectorProjector features Rear view Projector exterior viewFront and upper side view Under viewFocus ring Controls and functionsControl panel Remote control Front Table Positioning your projectorChoosing a location Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenScreen dimensions Projection distance D Lowest Highest Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen aspect ratio is 43 and the projected picture isShifting the projection lens To use the lens shift leverPreparations Connecting with video equipmentConnecting Hdmi devices Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cablePreparations Using the projectorTurning the projector on Using the OSD menu Fine-tuning the image size and clarityUsing the remote control or projector Selecting an input sourceUse / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Write down the number and turn off your projectorCorrecting picture distortion Adjusting the projected imageAdjusting the projection angle Ii. See step iii below for further operationFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Fine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To adjust and store the settings Color ManagementSelecting the aspect ratio Setting Film ModeSetting 3D Comb Filter About the aspect ratioUsing Panamorph lenses optional Aspect ratio Aspect ratio imageTo activate High Altitude Mode Operating in a high altitude environmentMain Source or PIP Source and press ENTER. The source To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Using the 3D menus Watching 3D contentConnecting 3D video devices Personalizing the projector menu displayTo lock the keys Locking control keysTurning the projector off Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information System SetupAdvanced Setup Function Description Picture -- Basic menuPicture -- Advanced menu Display menu System Setup menu Advanced Setup menuInformation menu Additional information Care of the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Connecting with video equipment Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionYour Blu-ray Disc is not in 3D TroubleshootingProblem Cause Remedy FormatOptical SpecificationsGeneral characteristics ElectricalDimensions 317 145 428Refresh rate Frequency Pixel Format Timing chartSupported timing for PC input KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Supported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationWarranty Disclaimer
Top Page Image Contents