BenQ W7000+ user manual Indicators, Power Temp Lamp Status & Description

Page 49

Indicators

There are three indicators which show the status of the projector. Check the following for information about the indicator lights. If there is anything wrong, turn the projector off and contact your dealer.

When the projector is in a normal state

		Power	Temp	Lamp	Status & Description
		Orange	Off	Off	Stand-by mode

		Green	Off	Off	Powering up
		Flashing	Off	Off	Powering up
		Flashing

		Green	Off	Off	Normal operation

					• The projector needs 90 seconds to cool down as it was
		Orange			abnormally shut down without the normal cooling down
		Orange	Off	Off	process.
		Flashing	Off	Off	process.
		Flashing			• The projector needs to cool for 90 seconds after the power

					is turned off.

		When the projector is in an abnormal state



		Power	Temp	Lamp	Status & Description
		Off	Off	Red	• The lamp has been damaged. Please contact your local BenQ
		Off	Off	Red	customer center for purchasing a new lamp.
					customer center for purchasing a new lamp.

					• The lamp is not properly attached.
		Orange	Off	Red	• The lamp has been damaged. Please contact your local BenQ
					customer center for purchasing a new lamp.

		Off	Red	Off

		Off	Red	Red	The fans are not working.

		Off	Red	Green
		Off	Red	Green

		Off	Red	Orange

		Off	Green	Red	Fan sensors error	The projector has shut down
		Off	Green	Orange	Fans do not rotate during	The projector has shut down
		Off	Green	Orange	Fans do not rotate during	automatically. If you try to re-
					powering up.	automatically. If you try to re-
		Off	Orange	Red	powering up.	start the projector, it will shut
		Off	Orange	Red		start the projector, it will shut
						down again. Please contact your
		Red	Red	Red		down again. Please contact your
		Red	Red	Red		dealer for assistance.

		Red	Red	Green
		Red	Red	Green

		Red	Red	Orange	Thermal condition error

		Green	Red	Red
		Green	Red	Red

		Green	Red	Green

		Green	Red	Orange

		Orange	Red	Red	The internal temperature is too high.
		Orange	Red	Green	• The intake ventilation or the exhaust ventilation is blocked.

		Orange	Red	Orange	• The projector may be in a poorly ventilated location.
		Orange	Red	Orange	• The ambient temperature may be too high.
					• The ambient temperature may be too high.

Connecting with video equipment

49

Image 49

Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control operation Remote control batteriesRemote control reaching the projector Ceiling mounting the projectorProjector features Front and upper side view Projector exterior viewRear view Under viewControl panel Controls and functionsFocus ring Remote control Choosing a location Positioning your projectorFront Table Determine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsFloor Installation Ceiling Installation Installation for a 43 ratio screenScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isTo use the lens shift lever Shifting the projection lensConnecting Hdmi devices Connecting with video equipmentPreparations Connecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerTurning the projector on Using the projectorPreparations Using the remote control or projector Fine-tuning the image size and clarityUsing the OSD menu Selecting an input sourceUsing a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Ii. See step iii below for further operationSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Resetting the picture mode Setting the User 1/User 2/User 3 modeTo reset the picture mode to the preset factory values Fine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color Color Management To adjust and store the settingsSetting 3D Comb Filter Setting Film ModeSelecting the aspect ratio About the aspect ratioAspect ratio Aspect ratio image Using Panamorph lenses optionalOperating in a high altitude environment To activate High Altitude ModeDisplaying more than one image source simultaneously To display the PIP window Using the remote controlMain Source or PIP Source and press ENTER. The source Connecting 3D video devices Watching 3D contentUsing the 3D menus Personalizing the projector menu displayTurning the projector off Locking control keysTo lock the keys On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Advanced Setup System SetupInformation Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu Advanced Setup menu System Setup menuInformation menu Care of the projector Additional informationSetting Auto Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hour Replacing the lamp Timing of replacing the lamp Status Message Connecting with video equipment Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsProblem Cause Remedy TroubleshootingYour Blu-ray Disc is not in 3D FormatGeneral characteristics SpecificationsOptical Electrical317 145 428 DimensionsSupported timing for PC input Timing chartRefresh rate Frequency Pixel Format KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Format Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty Warranty and Copyright informationCopyright Disclaimer