BenQ W7000+ Utilizing the password function, Setting a password, If you forget the password

Page 23

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. Once the password is set and this function is selected, the projector is password-protected. Users who do not know the correct password can not use the projector.

You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.

Setting a password

Once a password has been set and activated, the projector cannot be used unless the correct password is entered every time the projector is started.

1.Press MENU on the projector or remote control and then press /

until the Advanced Setup menu is highlighted.

2.Press to highlight Password and press ENTER. The Password page displays.

3.Highlight Change Password and press ENTER. The Input Password page displays.

4.As the picture indicates, the four arrow keys ( , , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys on the remote control or projector to enter six digits for the password.

Confirm the new password by re-entering the new password. Once the password is set, the OSD menu returns to the Password page.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

5.Highlight Power On Lock and then press / to select On.

6.Confirm the current password.

7.To leave the OSD menu, press MENU.

Advanced Setup

Lamp Settings

HDMI Settings

 

 

Baud Rate

115200

 

Test Pattern

 

 

High Altitude Mode

Off

Password

ENTER

Key Lock

Off

Reset All Settings

 

 

ISF

 

 

S-Video

Back

Password

 

 

 

 

 

Change Password

ENTER

Power On Lock

Off

 

 

Back

Input New Password

Back

If you forget the password

If the password function is activated, you will be asked to enter the six- digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right displays lasting for three seconds, and the Input Password page follows. You can retry by entering another six-digit password, or if you did not record the password in this manual, and you absolutely do not remember it, you can use the password recall procedure. See "Entering the password recall procedure" on page 24 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

Password Error

Please try again.

Connecting with video equipment

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Disposal Moisture condensationAvoid volatile liquids Overview Shipping contentsCeiling mounting the projector Remote control batteriesRemote control operation Remote control reaching the projectorProjector features Under view Projector exterior viewFront and upper side view Rear viewFocus ring Controls and functionsControl panel Remote control Front Table Positioning your projectorChoosing a location Determine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsScreen aspect ratio is 43 and the projected picture is Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen dimensions Projection distance D Lowest HighestTo use the lens shift lever Shifting the projection lensPreparations Connecting with video equipmentConnecting Hdmi devices Connecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Using the projectorTurning the projector on Selecting an input source Fine-tuning the image size and clarityUsing the remote control or projector Using the OSD menuSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup menuIf you forget the password Utilizing the password functionSetting a password Write down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionIi. See step iii below for further operation Adjusting the projected imageAdjusting the projection angle Correcting picture distortionFine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To reset the picture mode to the preset factory values Setting the User 1/User 2/User 3 modeResetting the picture mode Fine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting Color Management To adjust and store the settingsAbout the aspect ratio Setting Film ModeSetting 3D Comb Filter Selecting the aspect ratioAspect ratio Aspect ratio image Using Panamorph lenses optionalOperating in a high altitude environment To activate High Altitude ModeMain Source or PIP Source and press ENTER. The source To display the PIP window Using the remote controlDisplaying more than one image source simultaneously Personalizing the projector menu display Watching 3D contentConnecting 3D video devices Using the 3D menusTo lock the keys Locking control keysTurning the projector off Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure Information System SetupAdvanced Setup Function Description Picture -- Basic menuPicture -- Advanced menu Display menu Advanced Setup menu System Setup menuInformation menu Care of the projector Additional informationGetting to know the lamp hour Setting Lamp Power as EconomicSetting Auto Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Connecting with video equipment Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsFormat TroubleshootingProblem Cause Remedy Your Blu-ray Disc is not in 3DElectrical SpecificationsGeneral characteristics Optical317 145 428 DimensionsKHz Timing chartSupported timing for PC input Refresh rate Frequency Pixel FormatUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Supported timing for Video and S-Video inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsDisclaimer Warranty and Copyright informationWarranty Copyright
Top Page Image Contents