BenQ W7000+ user manual Important safety instructions

Page 3

Thank you for your purchase of this quality BenQ video projector! It has been designed to provide you with an enjoyable home theater viewing experience. For the best results, please read this manual through carefully as it is your guide through the control menus and operation.

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

1.Please read this user manual before you operate your projector. Keep this manual in a safe place for future reference.

2.Always place the projector on a level, horizontal surface during operation.

-Do not place the projector on an unstable cart, stand, or table as it may fall and be damaged;

-Do not place inflammables near the projector;

-Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back.

3.Do not store the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage.

4.Do not place the projector in any of the following environments:

-space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector;

-locations where temperatures may become excessively high, such as the inside of a car with all windows closed;

-locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector’s lifespan and darken the screen;

-locations near fire alarms;

-locations with an ambient temperature above 35°C/95°F;

-locations where altitude is higher than 1500 meters/4920 feet above sea level.

4920-

9840

feet

Important safety instructions

3

Image 3
Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contentsCeiling mounting the projector Remote control batteriesRemote control operation Remote control reaching the projectorProjector features Under view Projector exterior viewFront and upper side view Rear viewControls and functions Control panelFocus ring Remote control Positioning your projector Choosing a locationFront Table Determine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsScreen aspect ratio is 43 and the projected picture is Installation for a 43 ratio screenFloor Installation Ceiling Installation Screen dimensions Projection distance D Lowest HighestTo use the lens shift lever Shifting the projection lensConnecting with video equipment Connecting Hdmi devicesPreparations Connecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerUsing the projector Turning the projector onPreparations Selecting an input source Fine-tuning the image size and clarityUsing the remote control or projector Using the OSD menuSecuring the projector Using the menusUsing a security cable lock Use / to highlight the System Setup menuUtilizing the password function Setting a passwordIf you forget the password Write down the number and turn off your projector Entering the password recall procedureChanging the password Disabling the password functionIi. See step iii below for further operation Adjusting the projected imageAdjusting the projection angle Correcting picture distortionUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 mode Resetting the picture modeTo reset the picture mode to the preset factory values Fine-tuning the picture quality Controlling image clarity Setting Black LevelSelecting a color temperature Advanced picture quality controlsSetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color Color Management To adjust and store the settingsAbout the aspect ratio Setting Film ModeSetting 3D Comb Filter Selecting the aspect ratioAspect ratio Aspect ratio image Using Panamorph lenses optionalOperating in a high altitude environment To activate High Altitude ModeTo display the PIP window Using the remote control Displaying more than one image source simultaneouslyMain Source or PIP Source and press ENTER. The source Personalizing the projector menu display Watching 3D contentConnecting 3D video devices Using the 3D menusLocking control keys Turning the projector offTo lock the keys On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup Advanced SetupInformation Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu Advanced Setup menu System Setup menuInformation menu Care of the projector Additional informationGetting to know the lamp hour Setting Lamp Power as EconomicSetting Auto Off Lamp informationTiming of replacing the lamp Replacing the lampStatus Message Connecting with video equipment Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsFormat TroubleshootingProblem Cause Remedy Your Blu-ray Disc is not in 3DElectrical SpecificationsGeneral characteristics Optical317 145 428 DimensionsKHz Timing chartSupported timing for PC input Refresh rate Frequency Pixel FormatUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Supported timing for Video and S-Video inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Edtv and Hdtv via Component inputsDisclaimer Warranty and Copyright informationWarranty Copyright