BenQ W7000+ user manual Resetting the lamp timer

Page 48

Resetting the lamp timer

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.

1.After the start-up logo, press MENU and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Lamp Settings and press ENTER. The Lamp Settings page displays.

3.Highlight Reset Lamp Timer and press ENTER. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press ENTER. The lamp time will be reset to "0".

Advanced Setup

Lamp Settings	ENTER
HDMI Settings
Baud Rate	115200
Test Pattern
High Altitude Mode	Off
Password
Key Lock	Off
Reset All Settings
ISF
S-Video	Back
Lamp Settings
Lamp Power	Normal
Reset Lamp Timer	ENTER
Equivalent Lamp Hour	50
	Back

Reset Lamp Timer

Reset Lamp Timer?

Reset Cancel

48 Connecting with video equipment

Image 48

Contents W7000/W7000+ Digital Projector Home Cinema Series Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationRemote control reaching the projector Ceiling mounting the projectorProjector features Projector exterior view Front and upper side viewRear view Under viewControls and functions Control panelFocus ring Remote control Positioning your projector Choosing a locationFront Table Obtaining a preferred projected image size Determine the aspect ratio of your screen, 169 or 43?Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen Floor Installation Ceiling InstallationScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isShifting the projection lens To use the lens shift leverConnecting with video equipment Connecting Hdmi devicesPreparations Connecting component-video devices Connecting S-Video or video devicesConnecting a computer Connect the projector to a computer with a VGA cableUsing the projector Turning the projector onPreparations Fine-tuning the image size and clarity Using the remote control or projectorUsing the OSD menu Selecting an input sourceUsing the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Write down the number and turn off your projectorAdjusting the projected image Adjusting the projection angleCorrecting picture distortion Ii. See step iii below for further operationUsing the preset and user modes Selecting a preset modeFine-tuning the selected picture mode Setting the User 1/User 2/User 3 mode Resetting the picture modeTo reset the picture mode to the preset factory values Fine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To adjust and store the settings Color ManagementSetting Film Mode Setting 3D Comb FilterSelecting the aspect ratio About the aspect ratioUsing Panamorph lenses optional Aspect ratio Aspect ratio imageTo activate High Altitude Mode Operating in a high altitude environmentTo display the PIP window Using the remote control Displaying more than one image source simultaneouslyMain Source or PIP Source and press ENTER. The source Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu displayLocking control keys Turning the projector offTo lock the keys On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup Advanced SetupInformation Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu System Setup menu Advanced Setup menuInformation menu Additional information Care of the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Connecting with video equipment Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyYour Blu-ray Disc is not in 3D FormatSpecifications General characteristicsOptical ElectricalDimensions 317 145 428Timing chart Supported timing for PC inputRefresh rate Frequency Pixel Format KHzUxga Supported timing for Hdmi Hdcp input 1440 x WXGA+60 59.887 55.935 106.500 Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty and Copyright information WarrantyCopyright Disclaimer