Runco SP-42DHD Installation, Considerations, High-Altitude Operation, Mounting the PlasmaWall

Page 30

Installation

3.3	Proper installation of your PlasmaWall will ensure the highest possible picture quality.
Installation	Whether you are installing the PlasmaWall temporarily or permanently, you should take the
Considerations	following into account to ensure that it performs optimally.

High-Altitude Operation ➤	Due to the design of all plasma glass panels made by every manufacturer, and the
	interaction between ambient air pressure and the plasma gases contained inside of the
	panel, reliable operation of your plasma display cannot be assured during operation at
	certain high-altitude locations.
	Runco has found this plasma monitor to operate reliably at altitudes of up to 6000 MSL
	(mean sea level). At elevations higher than this, each panel may react differently,
	depending upon the altitude, air pressure, humidity and other meteorological factors.
	For this reason, Runco International makes no warranties or claims as to the reliable
	operation of the SP-42DHD at altitudes greater than 6000 feet above sea level. If you are
	planning to use this product at a location above 6000 feet, please contact Runco
	technical support for further information.
Mounting the PlasmaWall ➤	To install the PlasmaWall, you will need either an optional table stand or wall-mounting kit.
on a Wall or Table Stand	The PlasmaWall cannot be installed on its own.
	If you do decide to wall-mount the PlasmaWall, ensure that the wall-mount bracket is
	installed according to the instructions included with it. The wall must be capable of
	supporting a redundant weight factor three (3) times the weight of the display, or be
	reinforced.
	Runco recommends that this be done by a custom installation specialist.
	Note	Use only a Runco-approved wall-mount kit or table stand that is
		specifically designed for your display.

You can attach your optional mounts or stand to the PlasmaWall in either of two ways:

• While it is upright.

20	PlasmaWall SP Series Owner’s Operating Manual

Image 30

Contents SP-42DHD SP-50DHD SP-60DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Appendix A. PlasmaWall Service Remote Control Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsPlasmaWall at a Glance PlasmaWall Model SP-42DHD Rear Panel PlasmaWall Model SP-50DHD Rear Panel PlasmaWall Model SP-60DHD Rear Panel External Speaker Output Right Main Power SwitchDigital RGB Input 2 DVI-D External Speaker Output LeftRunco Icon Power ButtonDHD Controller Front Panel IR SensorEnter Button UP ButtonLeft Button Down ButtonDVI OUT Component Video RCA connectorsDHD Controller Rear Panel Inputs 3. DVI 1 / DVI 2 DigitalComposite Video Input RS-232 Control PortMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlLight IR Output IndicatorEnter MenuISF Night CinemaSVC ISF DAYInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toHigh-Altitude Operation InstallationConsiderations Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall DVI Connections See Figure Connecting SourceComponents to the DHD DVI Source DVD Player or HD Tuner with Hdmi or DVI outDigital DTV RGB Connections See Digital DTV RGB ConnectionsRefer to Computer/Video Signal Compatibility on page 64 for Analog Computer RGB Connections See FigurePersonal Computer Composite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting 12-Volt Trigger Outputs to External Equipment RS-232 ControllerConnection 11. Installing the Cable Ties Turning on the Power OperationYou must enter a passcode to access the Service menu Operation Using the On-Screen Menus Input Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Number Hardware Firmware 0002.034B Date Nov 25Gain/Offset Refer to ISF Night Display Color, above CalibrationService Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionComputer/Video Signal Maintenance and Troubleshooting Serial Communications Letterbox EnterInput Selection Commands CommandValue Description Min/max Stored? Power On/Off Commands Aspect Ratio CommandsImage Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Command Parameter min/max Value Stored? Description Enter keyModel SP-42DHD SpecificationsPlasmaWall Specifications Model SP-50DHDDHD Controller Specifications Dimensions PlasmaWall14.8 34.3 49.1 M8 Screw Horiz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks KHz56.0 45.1 Specifications Figure A-1. PlasmaWall Service Remote Control OverviewRGB-HD RGB SetupAspect Ratio DVI-DService/Setup Menu Video NR NoiseReduction PlasmaWall Service Remote Control Page Runco CL-810 Owner’s Operating Manual