Runco SP-42DHD, SP-60DHD Aspect Ratio, Rgb-Hd, Dvi-D, SET Button, Mute, RGB Setup, Info, Magnify

Page 78

PlasmaWall Service Remote Control

The PlasmaWall service remote control is intended for use only by Note authorized Runco dealers. Use it only as described here or as

instructed to by Runco Technical Support.

1.ASPECT RATIO

Press this button repeatedly to select a display aspect ratio (this may be necessary with certain computer resolutions).

2.Input Selection Buttons:

RGB-HD

Selects INPUT 1 (ANALOG RGB IN) on the PlasmaWall.

DVI-D

Selects INPUT 2 (DIGITAL RGB) on the PlasmaWall.

3.MENU

Pressing the MENU button brings up the main menu. Also, if you are in an adjustment mode or function, pressing MENU brings the menu back one level.

4.Directional Buttons ( / / / )

Use these buttons to navigate the OSD menus and adjust various settings.

5.SET BUTTON

When an item is highlighted on the On-Screen Display, the SET button selects the item.

6.MUTE

Not used with the PlasmaWall.

7.RGB SETUP

When using INPUT 1 to display images from a computer, press this button to automatically set the Position, Clock and Phase settings to their optimum values.

8.STANDBY/ON ( )

Press to put the display into operation or standby mode.

9.INFO

Displays currently-selected input, aspect ratio and signal timing information.

10.INSTALLER ADJUST (pin hole)

Used to access the INSTALLER ADJUST menu.

11.MAGNIFY

Press this button to select and enlarge one part of the screen image.

12.VOLUME + / -

Not used with the PlasmaWall.

A-2	PlasmaWall SP Series Owner’s Operating Manual

Image 78

Contents SP-42DHD SP-50DHD SP-60DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Appendix A. PlasmaWall Service Remote Control Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsPlasmaWall at a Glance PlasmaWall Model SP-42DHD Rear Panel PlasmaWall Model SP-50DHD Rear Panel PlasmaWall Model SP-60DHD Rear Panel External Speaker Output Right Main Power SwitchDigital RGB Input 2 DVI-D External Speaker Output LeftRunco Icon Power ButtonDHD Controller Front Panel IR SensorEnter Button UP ButtonLeft Button Down ButtonDVI OUT Component Video RCA connectorsDHD Controller Rear Panel Inputs 3. DVI 1 / DVI 2 DigitalComposite Video Input RS-232 Control PortMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlLight IR Output IndicatorEnter MenuISF Night CinemaSVC ISF DAYInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toHigh-Altitude Operation InstallationConsiderations Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall DVI Connections See Figure Connecting SourceComponents to the DHD DVI Source DVD Player or HD Tuner with Hdmi or DVI outDigital DTV RGB Connections See Digital DTV RGB ConnectionsRefer to Computer/Video Signal Compatibility on page 64 for Analog Computer RGB Connections See FigurePersonal Computer Composite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnecting 12-Volt Trigger Outputs to External Equipment RS-232 ControllerConnection 11. Installing the Cable Ties Turning on the Power OperationYou must enter a passcode to access the Service menu Operation Using the On-Screen Menus Input Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Number Hardware Firmware 0002.034B Date Nov 25Gain/Offset Refer to ISF Night Display Color, above CalibrationService Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionComputer/Video Signal Maintenance and Troubleshooting Serial Communications Letterbox EnterInput Selection Commands CommandValue Description Min/max Stored? Power On/Off Commands Aspect Ratio CommandsImage Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Command Parameter min/max Value Stored? Description Enter keyModel SP-42DHD SpecificationsPlasmaWall Specifications Model SP-50DHDDHD Controller Specifications Dimensions PlasmaWall14.8 34.3 49.1 M8 Screw Horiz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks KHz56.0 45.1 Specifications Figure A-1. PlasmaWall Service Remote Control OverviewRGB-HD RGB SetupAspect Ratio DVI-DService/Setup Menu Video NR NoiseReduction PlasmaWall Service Remote Control Page Runco CL-810 Owner’s Operating Manual