Runco SP-50DHD, SP-42DHD, SP-60DHD manual PlasmaWall Service Remote Control

Page 80

PlasmaWall Service Remote Control

MPEG Filter ➤ Use the MPEG Filter to reduce or eliminate so-called “mosquito noise” in MPEG-compressed video signals (digital broadcasts or DVDs). Set it to LOW, MIDDLE or HIGH, as needed to minimize distortion around the edges of moving objects, moving artifacts around edges and/or blotchy noise patterns superimposed over the objects.

To change the MPEG Filter setting on INPUT 1:

1.Press 1 to switch to PlasmaWall INPUT 1.

2.Press MENU on the PlasmaWall Service Remote Control.

3.Press or to select SETUP.

4.Press to select MPEG FILTER, then press SET.

5.Press or to select the desired amount of filtering (OFF, LOW, MIDDLE or HIGH).

6.Press SET to confirm your selection.

A-4	PlasmaWall SP Series Owner’s Operating Manual

Image 80

Contents SP-42DHD SP-50DHD SP-60DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsAppendix A. PlasmaWall Service Remote Control OperationList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions PlasmaWall Model SP-42DHD Rear Panel PlasmaWall Model SP-50DHD Rear Panel PlasmaWall Model SP-60DHD Rear Panel Main Power Switch Digital RGB Input 2 DVI-DExternal Speaker Output Right External Speaker Output LeftPower Button DHD Controller Front PanelRunco Icon IR SensorUP Button Left ButtonEnter Button Down ButtonComponent Video RCA connectors DHD Controller Rear PanelDVI OUT Inputs 3. DVI 1 / DVI 2 DigitalMain AC Fuse Composite Video InputRS-232 Control Port DHD Controller Remote Control DHD Controller Remote ControlIR Output Indicator EnterLight MenuCinema SVCISF Night ISF DAYInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation ConsiderationsHigh-Altitude Operation Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source Components to the DHDDVI Connections See Figure DVI Source DVD Player or HD Tuner with Hdmi or DVI outDigital DTV RGB Connections See Digital DTV RGB ConnectionsPersonal Computer Refer to Computer/Video Signal Compatibility on page 64 forAnalog Computer RGB Connections See Figure Composite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection Connecting 12-Volt Trigger Outputs to External EquipmentRS-232 Controller 11. Installing the Cable Ties Turning on the Power OperationYou must enter a passcode to access the Service menu Operation Using the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.034B Date Nov 25Gain/Offset Refer to ISF Night Display Color, above CalibrationService Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Maintenance and Troubleshooting CleaningCleaning the Display Panel Body and Remote Control Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionComputer/Video Signal Maintenance and Troubleshooting Serial Communications Letterbox EnterCommand Value Description Min/max Stored? Power On/Off CommandsInput Selection Commands Aspect Ratio CommandsImage Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Command Parameter min/max Value Stored? Description Enter keySpecifications PlasmaWall SpecificationsModel SP-42DHD Model SP-50DHDDHD Controller Specifications Dimensions PlasmaWall14.8 34.3 49.1 M8 Screw Computer/Video Signal Compatibility Input Refresh Rate Resolution RemarksHoriz KHz56.0 45.1 Specifications Figure A-1. PlasmaWall Service Remote Control OverviewRGB Setup Aspect RatioRGB-HD DVI-DReduction Service/Setup MenuVideo NR Noise PlasmaWall Service Remote Control Page Runco CL-810 Owner’s Operating Manual