Runco SP-50DHD, SP-42DHD, SP-60DHD manual HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV

Page 56

Operation

Analog Out Mode: Select Analog Out Mode from the Service menu to change the characteristics of the analog output signal from the DHD Controller. The choices are RGB-- (separate sync with negative polarity), RGB++ (separate sync with positive polarity) or RGBS (composite sync).

Display Device: The options in the Display Device menu allow you to perform certain adjustments at the plasma display.

•Input Source: Select Input Source from the Display Device menu to switch from one DHD Controller output/PlasmaWall input to the other. Use the or button to select RGB or DVI/HDMI, then press ENTER.

Note

Tip

If the DVI 1 or DVI 2 DHD Controller input is active and the input signal is HDCP-encrypted, the RGBHV output of the DHD Controller is disabled.

Use the serial command DISPLAY 1 or DISPLAY 2 to set the Input Source to RGB or DVI/HDMI respectively, so that the DHD Controller retains this setting after a System Reset. (This is not the case when you change the Input Source in the Display Device menu.) For more information, refer to Miscellaneous Commands on page 57.

•Configure: Select Configure from the Display Device menu to perform the following display device adjustments (these are global, independent of any input):

•Select Left/Right or Up/Down and use the or buttons to fine-tune the displayed image position.

•Select Width or Height and use the or buttons to fine-tune the display device aspect ratio.

HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are known, select HD Format from the Service menu and set them as described below. Doing so can reduce the time it takes the DHD Controller to switch from HD to 480i signals or vice versa.

This is generally not necessary unless the DHD Controller – for whatever reason – has difficulty determining the color space (RGB or YUV), bandwidth or resolution of the incoming HD signal. In most situations, the Auto settings work well.

•HD/RGB 1 and HD/RGB 2 (Color Space): Select Auto, RGB or YUV.

•ADC Bandwidth: Select Auto, 75 MHz, 150 MHz or 300 MHz.

•YPbPr Input Resolution: Select Auto or specify the input resolution, if known: 480i, 480p, 576i, 576p, 720p or 1080i.

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

To save the trigger settings so that they can be restored after a System Reset (described below), press repeatedly to highlight “Save.” Then, press ENTER.

46

PlasmaWall SP Series Owner’s Operating Manual

Page 55 Page 57
Image 56
Page 55 Page 57
Contents SP-42DHD SP-50DHD SP-60DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsAppendix A. PlasmaWall Service Remote Control OperationList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions PlasmaWall Model SP-42DHD Rear Panel PlasmaWall Model SP-50DHD Rear Panel PlasmaWall Model SP-60DHD Rear Panel Main Power Switch Digital RGB Input 2 DVI-DExternal Speaker Output Right External Speaker Output LeftPower Button DHD Controller Front PanelRunco Icon IR SensorUP Button Left ButtonEnter Button Down ButtonComponent Video RCA connectors DHD Controller Rear PanelDVI OUT Inputs 3. DVI 1 / DVI 2 DigitalMain AC Fuse Composite Video InputRS-232 Control Port DHD Controller Remote Control DHD Controller Remote ControlIR Output Indicator EnterLight MenuCinema SVCISF Night ISF DAYInstallation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation ConsiderationsHigh-Altitude Operation Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source Components to the DHDDVI Connections See Figure DVI Source DVD Player or HD Tuner with Hdmi or DVI outDigital DTV RGB Connections See Digital DTV RGB ConnectionsPersonal Computer Refer to Computer/Video Signal Compatibility on page 64 forAnalog Computer RGB Connections See Figure Composite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection Connecting 12-Volt Trigger Outputs to External EquipmentRS-232 Controller 11. Installing the Cable Ties Turning on the Power OperationYou must enter a passcode to access the Service menu Operation Using the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.034B Date Nov 25Gain/Offset Refer to ISF Night Display Color, above CalibrationService Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Maintenance and Troubleshooting CleaningCleaning the Display Panel Body and Remote Control Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionComputer/Video Signal Maintenance and Troubleshooting Serial Communications Letterbox EnterCommand Value Description Min/max Stored? Power On/Off CommandsInput Selection Commands Aspect Ratio CommandsImage Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Command Parameter min/max Value Stored? Description Enter keySpecifications PlasmaWall SpecificationsModel SP-42DHD Model SP-50DHDDHD Controller Specifications Dimensions PlasmaWall14.8 34.3 49.1 M8 Screw Computer/Video Signal Compatibility Input Refresh Rate Resolution RemarksHoriz KHz56.0 45.1 Specifications Figure A-1. PlasmaWall Service Remote Control OverviewRGB Setup Aspect RatioRGB-HD DVI-DReduction Service/Setup MenuVideo NR Noise PlasmaWall Service Remote Control Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents