Runco SP-60DHD, SP-42DHD, SP-50DHD manual Input Names Restore Composite Video Component SD, Save

Page 55

Input Names: You can give each DHD Controller input a descriptive name. For example, you may want to change the default input name to the type of source component connected to it: “VCR,” “DVD,” “Laptop” et cetera. Composite, S-Video and Component SD input names can be up to 12 characters long; the others can be up to eight characters long.

To edit an input name, select Input Names from the Service menu. Press or to select an input and press ENTER. Use the or buttons to change a character; press or to select a character to change. When you have finished editing the input name, press MENU.

To restore the default input name, press repeatedly to highlight that input name in the “Restore” column. Then, press ENTER.

To save input names so that they can be restored after a System Reset (described on page 47), press repeatedly to highlight “Save.” Then, press ENTER.

The button takes you from top to bottom in the left column, then

Note from top to bottom in the right column. To highlight “Save,” scroll through both columns.

Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the DHD Controller will respond. By default, both are set to

17. You can change these codes if either:

•Another device in the theater (a DVD player, for example) is responding to commands from the DHD Controller remote control (Figure 2-7)in ways that are unpredictable or undesirable.

•You have multiple DHD Controllers and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific device.

Use the DHD Controller front-panel keypad to change its IR code.

Tip Then, change the code sent by the remote to match as described below.

Do not change the “Type” setting in this menu.

Note

When you change a remote code on the DHD Controller, you must re-program your remote control to send that same code. To do this:

1. Using a straightened paper clip or similar object, press and hold the CODE button on the remote control for approximately three seconds, or until the red LED on the remote lights solid red.

2. Enter a new two-digit code between 00 and 31 inclusive. Include a leading zero for single-digit codes; for example, enter 9 as “09.”

3.The LED turns off to confirm the code change. If you enter an invalid code, the LED flashes for three or four seconds. Try again, entering a valid code.

Input Names

 

Restore

Composite

Composite

 

 

S-Video 1

S-Video 1

S-Video 2

S-Video 2

Component SD

Component SD

HD/RGB 1

HD/RGB 1

HD/RGB 2

HD/RGB 2

DVI 1

DVI 1

DVI 2

DVI 2

Save

 

PlasmaWall SP Series Owner’s Operating Manual

45

Page 54 Page 56
Image 55
Page 54 Page 56
Contents SP-42DHD SP-50DHD SP-60DHD Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. PlasmaWall Service Remote ControlList of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsPlasmaWall at a Glance PlasmaWall Model SP-42DHD Rear Panel PlasmaWall Model SP-50DHD Rear Panel PlasmaWall Model SP-60DHD Rear Panel External Speaker Output Left Main Power SwitchDigital RGB Input 2 DVI-D External Speaker Output RightIR Sensor Power ButtonDHD Controller Front Panel Runco IconDown Button UP ButtonLeft Button Enter ButtonInputs 3. DVI 1 / DVI 2 Digital Component Video RCA connectorsDHD Controller Rear Panel DVI OUTRS-232 Control Port Composite Video InputMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlMenu IR Output IndicatorEnter LightISF DAY CinemaSVC ISF NightRemote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupMounting the PlasmaWall InstallationConsiderations High-Altitude OperationVentilation Ambient LightInstallation Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall DVI Source DVD Player or HD Tuner with Hdmi or DVI out Connecting SourceComponents to the DHD DVI Connections See FigureDigital DTV RGB Connections Digital DTV RGB Connections SeeAnalog Computer RGB Connections See Figure Refer to Computer/Video Signal Compatibility on page 64 forPersonal Computer DVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureRS-232 Controller Connecting 12-Volt Trigger Outputs to External EquipmentConnection 11. Installing the Cable Ties Operation Turning on the PowerYou must enter a passcode to access the Service menu Operation Using the On-Screen Menus Aspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input Position Serial Number Hardware Firmware 0002.034B Date Nov 25 ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration Gain/Offset Refer to ISF Night Display Color, aboveShould be used by ISF-certified technicians only ServiceInput Names Restore Composite Video Component SD HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlSymptom Possible Causes Solution Troubleshooting TipsComputer/Video Signal Maintenance and Troubleshooting Letterbox Enter Serial CommunicationsAspect Ratio Commands CommandValue Description Min/max Stored? Power On/Off Commands Input Selection CommandsImage Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Enter key Command Parameter min/max Value Stored? DescriptionModel SP-50DHD SpecificationsPlasmaWall Specifications Model SP-42DHDDHD Controller Specifications PlasmaWall Dimensions14.8 34.3 49.1 M8 Screw KHz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks Horiz56.0 45.1 Specifications Overview Figure A-1. PlasmaWall Service Remote ControlDVI-D RGB SetupAspect Ratio RGB-HDVideo NR Noise Service/Setup MenuReduction PlasmaWall Service Remote Control Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents