Pioneer PDK-50HW3 Installing the Driver, Connecting a Scan Device to a Computer, Screen burning

Page 21

3. Installation Procedures

3.4.2 Screen burning

Refer to “Screen Burning” in the Technical Manual supplied with the plasma display.

3.5 Installing the Driver

1.Install CBdrvU.

Refer to “Installing the CBdrvU (Ver. 2.0) Driver” on page 25.

2.Reboot the computer.

3.6 Connecting a Scan Device to a Computer

Connect the unit’s USB cable to the computer. (Connect to the USB1.1 or USB2.0 port.)

USB cable

Computer

Note:

When connecting a USB hub, use only self-powered types (with AC outlet power connection) with the capacity to provide 500mA

current.

When a USB cable is connected, the accompanying screen message will appear:

The power indicator will flash orange, and then flash alternately in green and orange. Do not touch the screen while the indicator is flashing, since automatic settings are being made during this time. There are no requirements regarding power on/off operation.

Image 21

Contents Technical Manual Ver Changes from PDK-50HW2A to PDK-50HW3 Pioneer badge need no longer be removed during installationScan device changes New designFlash pattern of the power indicator has changed Location of the PEN-NORMAL mode selector switch has changedUSB cable clip location Changes made to the pen Pen stand modificationsChanges in the driver Pen stand has been modifiedChanges in service Service Mode has been improvedMiddle button 3-button emulation is supported Contents Specifications SpecificationsSystem plasma display and handwriting device specifications Separate plasma display PDP-504CMX specificationsAccessories Plasma display monitor PDP-504CMX/PDP-50MXE1/PDP-50MXE1-SHandwriting device PDK-50HW3 Outline Drawing External dimension drawingSide panel Plasma displayPDK-50HW3 as seen from rear PDK-50HW3 center line USB cable exitConfirming Battery Life ¶ External dimension drawingName and Function of Parts & Pin Layout ¶ Name and function of partsInstallation Site Installation SiteInstallation Conditions List showing compatibility of standard metal fittingsSpecial installations Installation of multiple systems Installation precautionsExposure to direct sunlight Ultrasonic wavesUnpacking Installation ProceduresTransportation precautions Installing the handwriting device PDK-50HW3 Assembly and ConnectionsBattery cover Changing the pen batteryConnecting the plasma display to a computer Computer Setup ExamplePrecautions regarding computer setup CheckProcedures for setting the plasma display Adjusting the Plasma DisplayInstalling the Driver Connecting a Scan Device to a ComputerScreen burning Check in Service Mode How to Use Cable ClipCheck in Normal mode Check in PEN mode¶ Alignment of pen tip and cursor position Final Check Installing the CBdrvU Ver .0 Driver Installing and Using SoftwareInstallation procedures Operating environmentUninstall procedures Using the DriverChanges from CBdrv Ver .4 to CBdrvU Ver CBdrvU operationsHot key operations Scan device setup screen Select Calibration dialogScan device off screen Calibration Detail-1 OK buttonCalibration Detail-2 Easy SettingDouble-click area Property screenDouble-click speed Other setupTest Mode Test chart displayState display About CBdrvU Disabling CBdrvUExit Disabling CBdrvURotate CBdrvU operationTask tray display Precautions Installing and Using Software Service Mode display Using Driver and Service ModeScreen items Status displayed after pressing SelfTest buttonInstalling and Using Software Readjustment of White Balance Maintenance and CleaningScreen Name Part NumberReplacing the pen tip Pen battery lifeInternal DIP Switch Settings To lock device in the Normal modeTo make waveform observations Hardware-Related Q&A Page Driver Software-Related Q&A Page Troubleshooting Problem Possible SolutionPlasma Display PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S Error messege Remedy TroubleshootingHandwriting Device PDK-50HW3 Symptom Cause SolutionLow scan mode ResolutionHigh scan mode Capabilities of the Handwriting Device