Panasonic WJ-HD500B manual Installation, Installing the Optional Hard Disk

Page 12

INSTALLATION

The installations described below should be made by qualified service personnel or system installers.

■Installing the Optional Hard Disk

At the time of shipment from the factory, the WJ-HD500B Disk Recorder is equipped with one hard disk drive; an optional drive can be installed to increase the hard disk storage capacity.

To install the optional hard disk, follow the procedures below.

1.Unplug the power cord from the WJ-HD500B Disk Recorder, or disconnect the plug from the AC outlet.

2.Remove one screw on the control panel shown in the figure, then remove the panel by sliding it to the left and turned over.

FS 16

3.Remove two screws on the tray chassis in the figure, then slide out the chassis from the Disk Recorder.

FS 16

4.Insert the absorbers on to the chassis as shown in the figure.

5.Place the hard disk on the chassis, then fix it with the four screws and sleeves with the earth lug as shown in the figure.

absorber

earth lug

sleeve

6.Set the unit address with the jumper connector on the hard disk drive, as shown in the figure, for example.

7.Install the hard disk with the chassis into the Disk Recorder by sliding it from the front.

8.Plug in the power cable and interface flat cable pre- pared in the power inlet and interface connector of the hard disk as shown in the figure.

9.After installing the hard disk, secure the tray chassis and control panel by tightening the screws.

12

Image 12

Contents Operating Instructions Lightning flash with arrowhead symbol Contents Features PrefaceReliable recording of events Easy image searchPrecautions Front View @4Alarm Search Button Alarm Search @8Setup/Escape Button SETUP/ESC1Numeric Buttons 1 2Set Button SET@9Direction Buttons CDA B #0Full Indicator Full #1Hard Disk Drive Indicator HDD$1Multiscreen Output Connector Multiscreen OUT $22Spot Output Connector Spot OUT$7Alarm Port Alarm $9Mode Selector Mode2Gen-lock Output Connector GEN-LOCK OUT 8Power Switch Power ON/OFFWV-CU50 Remote Controller 1Lock Button Lock2Monitor Selection Button 3Multiscreen Selection Button9Alarm Search Button Alarm Search 1Link Indicator LinkBlinking Pause mode 0JogDial 6Electronic Zoom Button EL-ZOOMInstallation Installing the Optional Hard DiskInstalling the Optional Network Board Installing the Optional Motion Detector Board Mounting into the Rack Connections Basic SystemSystem Expansion Shown below are examples of system connectionsConnection with the Remote Controller Connection with the Camera SitesConnection with the Monitors Alarm Port Connection AlarmControl Port Connection Connection with the Uninterrupted Power Supply UPS Connection with Control outputSwitch Setting Connection with the Extension UnitsScsi Connection ModeSwitch Settings Connection with the DVD Extension UnitConnection with the DVD Extension Unit without HDD Connection with the DVD Extension Unit with HDD Copy WJ-HDE510B EXTMode Selector Setting Connection to PS Data Compatible EquipmentSerial Port Connection 10/100BASE-T Port ConnectionPage Preparations Power UP Procedure Formatting the Hard Disk 1DISK Format Formatting the DVD-RAM Disk Mirroring Function To deactivate the mirror function Disk Remove Monitors and Displays Spot and Multiscreen MonitorStatus Display Time DisplayFormat Error or System Status DisplayGroup Display Electronic Zoom DisplayTimer Recorder Hard DiskManual Recorder Emergency RecorderTime Lapse Recording Multi Shot RecordingDynamic Recording is set to OFF One Shot Recording Dynamic Recording is set to ALM-ONLYPage Setup Procedures Setup Menu Displaying the Setup MenuProgramming Menu Setup Setup Timer Setting Recording SetupDisplay Setup Communication Setup Timer Setting Recording Setup Recording Quality SetupVideo Pixels Resolution Color Mode SettingGroup Setup Group Title SetupCamera Assignment SpaceThumbnail Display Setup Playback Mode SetupShuttle Speed Setup Recording of the Title DisplayHard Disk End Setup Manual Recording Mode Setting→ Manual with Audio → Manual Without Audio → Event Recording Manual Recording Alarm Active Mode Manual Recording Program TimerSpecial Day Timer External Program Timer Time Lapse Recording Internal TimerAlarm Active Mode Event RecordingMulti Shot Recording Internal Timer One Shot Recording Internal Timer Emergency Recording Time Lapse Recording Multiplexer Setup Sequence Setup Multiscreen MonitorLive Sequence Pattern Setting Live SequenceQuad Shift Setting Quad Pattern SetupSequence Timing Setting Sequence Setup Spot Monitor Group Multi Sequence SettingAuto Skip Setting Live Sequence Pattern SettingPower on Setting Multiscreen Monitor Power on Setting Spot MonitorSequence Timing Setting Secret View Setting Alarm Setup Alarm Port SettingAlarm Auto Reset Setting Alarm Output SettingAlarm Buzzer Setting Video Loss Alarm SettingVideo Motion Detector Setting Alarm Mode on the Multiscreen Monitor Alarm Mode on the Spot MonitorDisplay Setup Camera Title SetupDisplay Setting Multiscreen Monitor Clock DisplayTitle Display Setting Spot Monitor Alarm Display SettingTitle Display Status DisplayClock and Status Display Position Setting Title Display Position SettingCommunication Setup PS Data SetupUnit Address Setting Baud RateAlarm Data Input Camera Number SetupParity Check Stop BitRS-232C Setup Network Setup System Setup Clock SetupTime Adjustment Setting SET TimePassword Lock Setting Buzzer SettingUser Defined Setting Auto Button Locked SettingDisk Space Indicator Disk ManagementDisk Information Error Report System InformationDVD Drive Setup Alarm Recording BackupDVD Format Emergency Recording Backup DVD Disk End SetupDisk Space Display Page Operating Procedures Controlling the Video Input and Monitors Controlling the Spot MonitorSelecting the Spot Monitor Single Spot LiveControlling the Multiscreen Monitor Selecting the Multiscreen MonitorZooming Single Spot Live Group Single Sequence Live Multiscreen Spot Live Multiscreen SelectAll Input Display with Quad Shift Off Multi Sequence Live All Input Display with Quad Shift On Group DisplayMulti Group setting Quad setting Group Multi SequenceAlarm Control Function Alarm InputAlarm Operation Alarm Reset Alarm SuspensionManual Reset Auto ResetInternal Timer Recording Power-on Time Lapse RecordingRecording Manual RecordingAlarm Recording Alarm Recording for Manual and Power-on RecordingSet to ALM-ONLY Alarm Recording for Internal Timer Modes Set to ALM-MULTITime Lapse Recording Emergency Recording Playback Basic PlaybackStop Forward or Backward searchAlarm jump search Search Record FunctionJump search Record ListAlarm Log Search DisplayTime & Date Search Display on the Monitor Single and Multiscreen Spot PlaybackZooming Single Spot Playback Displaying Camera and Playback Image REC PreviewBackup Function JogDialALM-VMD2 Total 931RECORD Data Erase Function Auto Erase FunctionManual Erase Function To release this function, follow the procedure below Button Locked FunctionLock Playback of Backup Data Specifications Standard AccessoryGeneral Input and OutputN1102-0 V8QA6084AN