Panasonic WJ-HD500B manual Alarm Recording for Manual and Power-on Recording, Set to ALM-ONLY

Page 89

Notes:

•When the TIMER parameter is set to EXT in the setup menu for Power-on Recording, the Internal Timer Recording is disabled.

•Make sure to keep the POWER switch on the rear of the Disk Recorder set to ON.

■Alarm Recording

The Disk Recorder activates the recording alarm status within the specified recording mode, when an externally connected alarm sensor is turned on, or when the installed Video Motion Detector (optional) is activated.

The alarm recording mode is determined by the setup in the WJ-HD500 SETUP menu. Described below is an alarm recording mode for each recording mentioned above.

Note: The received alarm is ignored when the Disk Recorder is recording images in the Emergency Recording. (the alarm log is stored in the ERROR REPORT table.)

●Alarm Recording for Manual and Power-on Recording

The Disk Recorder records an alarm status based on the setup made in the MANUAL REC SETUP menu of the WJ-HD500 SETUP menu.

It records the images as shown below in Time Lapse Recording mode with the specified recording rate, quality and duration. The recording pattern varies according to the setting for the Dynamic Recording (DYNAMIC REC) parameter.

•Set to OFF

Records all input images in sequence starting from video input which have activated alarm.

Start

Alarm 2 in

Alarm 3 in

C1

C2

C3

C4

C2

C3

C4

C5

C6

C3

C4

C5

C6

T

Thumbnail

T

Thumbnail

T

Thumbnail

•Set to ALM-PRI

Records the alarm-activated input images preferentially over other video inputs.

Start

Alarm 4 in

Alarm 15 in

C1

C2

C3

C4

C4

C1

C4

C2

C4

C15

C1

C4

C2

T

Thumbnail

T

Thumbnail

T

Thumbnail

•Set to ALM-ONLY

Records the particular images which have activated the alarm.

Start

Alarm 4 in

Alarm 15 in

C1

C2

C3

C4

C4

C4

C4

C4

C4

C15

C15

C15

C15

T

Thumbnail

T

Thumbnail

T

Thumbnail

89

Image 89

Contents Operating Instructions Lightning flash with arrowhead symbol Contents Preface FeaturesReliable recording of events Easy image searchPrecautions Front View @8Setup/Escape Button SETUP/ESC @4Alarm Search Button Alarm Search1Numeric Buttons 1 2Set Button SET#1Hard Disk Drive Indicator HDD @9Direction Buttons CDA B #0Full Indicator Full$1Multiscreen Output Connector Multiscreen OUT $22Spot Output Connector Spot OUT$9Mode Selector Mode $7Alarm Port Alarm2Gen-lock Output Connector GEN-LOCK OUT 8Power Switch Power ON/OFF1Lock Button Lock WV-CU50 Remote Controller2Monitor Selection Button 3Multiscreen Selection Button1Link Indicator Link 9Alarm Search Button Alarm SearchBlinking Pause mode 0JogDial 6Electronic Zoom Button EL-ZOOMInstalling the Optional Hard Disk InstallationInstalling the Optional Network Board Installing the Optional Motion Detector Board Mounting into the Rack Basic System ConnectionsSystem Expansion Shown below are examples of system connectionsConnection with the Monitors Connection with the Remote ControllerConnection with the Camera Sites Alarm Alarm Port ConnectionControl Port Connection Connection with Control output Connection with the Uninterrupted Power Supply UPSConnection with the Extension Units Switch SettingScsi Connection ModeConnection with the DVD Extension Unit without HDD Switch SettingsConnection with the DVD Extension Unit Copy WJ-HDE510B EXT Connection with the DVD Extension Unit with HDDConnection to PS Data Compatible Equipment Mode Selector Setting10/100BASE-T Port Connection Serial Port ConnectionPage Preparations Power UP Procedure Formatting the Hard Disk 1DISK Format Formatting the DVD-RAM Disk Mirroring Function To deactivate the mirror function Disk Remove Spot and Multiscreen Monitor Monitors and DisplaysStatus Display Time DisplaySystem Status Display Format Error orGroup Display Electronic Zoom DisplayHard Disk Timer RecorderManual Recorder Emergency RecorderDynamic Recording is set to OFF Time Lapse RecordingMulti Shot Recording Dynamic Recording is set to ALM-ONLY One Shot RecordingPage Setup Procedures Displaying the Setup Menu Setup MenuDisplay Setup Communication Setup Programming Menu SetupSetup Timer Setting Recording Setup Timer Setting Recording Quality Setup Recording SetupVideo Pixels Resolution Color Mode SettingGroup Title Setup Group SetupCamera Assignment SpacePlayback Mode Setup Thumbnail Display SetupShuttle Speed Setup Recording of the Title Display→ Manual with Audio → Manual Without Audio → Hard Disk End SetupManual Recording Mode Setting Event Recording Manual Recording Program Timer Alarm Active Mode Manual RecordingSpecial Day Timer Time Lapse Recording Internal Timer External Program TimerEvent Recording Alarm Active ModeMulti Shot Recording Internal Timer One Shot Recording Internal Timer Emergency Recording Time Lapse Recording Sequence Setup Multiscreen Monitor Multiplexer SetupLive Sequence Pattern Setting Live SequenceSequence Timing Setting Quad Shift SettingQuad Pattern Setup Group Multi Sequence Setting Sequence Setup Spot MonitorAuto Skip Setting Live Sequence Pattern SettingSequence Timing Setting Power on Setting Multiscreen MonitorPower on Setting Spot Monitor Secret View Setting Alarm Port Setting Alarm SetupAlarm Auto Reset Setting Alarm Output SettingVideo Motion Detector Setting Alarm Buzzer SettingVideo Loss Alarm Setting Alarm Mode on the Spot Monitor Alarm Mode on the Multiscreen MonitorCamera Title Setup Display SetupDisplay Setting Multiscreen Monitor Clock DisplayAlarm Display Setting Title Display Setting Spot MonitorTitle Display Status DisplayTitle Display Position Setting Clock and Status Display Position SettingPS Data Setup Communication SetupUnit Address Setting Baud RateInput Camera Number Setup Alarm DataParity Check Stop BitRS-232C Setup Network Setup Clock Setup System SetupTime Adjustment Setting SET TimeBuzzer Setting Password Lock SettingUser Defined Setting Auto Button Locked SettingDisk Information Disk Space IndicatorDisk Management System Information Error ReportDVD Format DVD Drive SetupAlarm Recording Backup Disk Space Display Emergency Recording BackupDVD Disk End Setup Page Operating Procedures Controlling the Spot Monitor Controlling the Video Input and MonitorsSelecting the Spot Monitor Single Spot LiveZooming Single Spot Live Controlling the Multiscreen MonitorSelecting the Multiscreen Monitor Group Single Sequence Live All Input Display with Quad Shift Off Multiscreen Spot LiveMultiscreen Select All Input Display with Quad Shift On Group Display Multi Sequence LiveGroup Multi Sequence Multi Group setting Quad settingAlarm Operation Alarm Control FunctionAlarm Input Alarm Suspension Alarm ResetManual Reset Auto ResetPower-on Time Lapse Recording Internal Timer RecordingRecording Manual RecordingSet to ALM-ONLY Alarm RecordingAlarm Recording for Manual and Power-on Recording Time Lapse Recording Alarm Recording for Internal Timer ModesSet to ALM-MULTI Emergency Recording Basic Playback PlaybackStop Forward or Backward searchSearch Record Function Alarm jump searchJump search Record ListTime & Date Search Alarm Log SearchDisplay Zooming Single Spot Playback Display on the MonitorSingle and Multiscreen Spot Playback REC Preview Displaying Camera and Playback ImageJogDial Backup FunctionALM-VMD2 Total 931RECORD Auto Erase Function Data Erase FunctionManual Erase Function Lock To release this function, follow the procedure belowButton Locked Function Playback of Backup Data Standard Accessory SpecificationsGeneral Input and OutputN1102-0 V8QA6084AN