Panasonic WJ-HD500B manual Power UP Procedure

Page 28

POWER UP PROCEDURE

Before operating the Disk Recorder, confirm that the cam- eras and peripherals are connected correctly and securely and all system components are turned on.

1.Turn on the Disk recorder by pressing the POWER switch located on the rear of the Disk Recorder. Make sure that the OPERATE indicator on the front panel is illuminated.

2.After you completed the start, the Disk Recorder will run through a series of instructions for the system on the Multiscreen Monitor.

[ SYSTEM CHECK ]

PLEASE WAIT

3.If the Disk Recorder is powered up successfully, the display as shown below appears, then the camera images appear on the monitor screen.

[ SYSTEM CHECK ]

SYSTEM CHECK DONE!

PLEASE WAIT

DISK MENU: [SETUP] KEY

Note:

If during a system check the display shown below appears on the monitor screen, it will be followed by the DISK MENU after five seconds.

[ SYSTEM CHECK ]

YOU HAVE TO CONFIGURE DISKS

PLEASE WAIT

DISK MENU
MAIN 1:¢¢GB 2:¢¢GB
EXT5 1:¢¢GB 2:¢¢GB			3:¢¢GB 4:¢¢GB
EXT4	1:*	2:*	3:ADD	4:ADD
EXT3	1:LOST	2:LOST	3:LOST	4:LOST
EXT2	1:LOST	2:LOST	3:LOST	4:LOST
EXT1	1:-	2:-	3:-	4:-
EXT0	1:-	2:-	3:-	4:-

EXT DVD:-

REMOVE FORMAT

RESTART

SELECT ITEM AND PRESS [SET] KEY

The DISK MENU-Display indicates the status of the hard disks, and shows the causes why this menu was called up.

•Optional Extension Unit is installed [ADD] Requires disk formatting in the Extension Unit.

•Replaced Hard Disk []]

Requires disk formatting for a replaced Hard Disk.

•Detached Hard Disk [LOST]

Requires disk relocation in the system.

•Hard Disk malfunctions []]

Refer servicing to qualified service personnel.

•Hard Disk access error [ERR]

¢¢GB indicates the hard disk capacity.

Note:

If the Disk Recorder is left in this state for about five minutes, it will automatically restart by reconfiguring the system (disk remove).

Normal camera images will appear on the monitor screen.

28

Image 28

Contents Operating Instructions Lightning flash with arrowhead symbol Contents Features PrefaceReliable recording of events Easy image searchPrecautions Front View @4Alarm Search Button Alarm Search @8Setup/Escape Button SETUP/ESC1Numeric Buttons 1 2Set Button SET@9Direction Buttons CDA B #0Full Indicator Full #1Hard Disk Drive Indicator HDD$1Multiscreen Output Connector Multiscreen OUT $22Spot Output Connector Spot OUT$7Alarm Port Alarm $9Mode Selector Mode2Gen-lock Output Connector GEN-LOCK OUT 8Power Switch Power ON/OFFWV-CU50 Remote Controller 1Lock Button Lock2Monitor Selection Button 3Multiscreen Selection Button9Alarm Search Button Alarm Search 1Link Indicator LinkBlinking Pause mode 0JogDial 6Electronic Zoom Button EL-ZOOMInstallation Installing the Optional Hard DiskInstalling the Optional Network Board Installing the Optional Motion Detector Board Mounting into the Rack Connections Basic SystemSystem Expansion Shown below are examples of system connectionsConnection with the Camera Sites Connection with the Remote ControllerConnection with the Monitors Alarm Port Connection AlarmControl Port Connection Connection with the Uninterrupted Power Supply UPS Connection with Control outputSwitch Setting Connection with the Extension UnitsScsi Connection ModeConnection with the DVD Extension Unit Switch SettingsConnection with the DVD Extension Unit without HDD Connection with the DVD Extension Unit with HDD Copy WJ-HDE510B EXTMode Selector Setting Connection to PS Data Compatible EquipmentSerial Port Connection 10/100BASE-T Port ConnectionPage Preparations Power UP Procedure Formatting the Hard Disk 1DISK Format Formatting the DVD-RAM Disk Mirroring Function To deactivate the mirror function Disk Remove Monitors and Displays Spot and Multiscreen MonitorStatus Display Time DisplayFormat Error or System Status DisplayGroup Display Electronic Zoom DisplayTimer Recorder Hard DiskManual Recorder Emergency RecorderMulti Shot Recording Time Lapse RecordingDynamic Recording is set to OFF One Shot Recording Dynamic Recording is set to ALM-ONLYPage Setup Procedures Setup Menu Displaying the Setup MenuSetup Timer Setting Recording Setup Programming Menu SetupDisplay Setup Communication Setup Timer Setting Recording Setup Recording Quality SetupVideo Pixels Resolution Color Mode SettingGroup Setup Group Title SetupCamera Assignment SpaceThumbnail Display Setup Playback Mode SetupShuttle Speed Setup Recording of the Title DisplayManual Recording Mode Setting Hard Disk End Setup→ Manual with Audio → Manual Without Audio → Event Recording Manual Recording Alarm Active Mode Manual Recording Program TimerSpecial Day Timer External Program Timer Time Lapse Recording Internal TimerAlarm Active Mode Event RecordingMulti Shot Recording Internal Timer One Shot Recording Internal Timer Emergency Recording Time Lapse Recording Multiplexer Setup Sequence Setup Multiscreen MonitorLive Sequence Pattern Setting Live SequenceQuad Pattern Setup Quad Shift SettingSequence Timing Setting Sequence Setup Spot Monitor Group Multi Sequence SettingAuto Skip Setting Live Sequence Pattern SettingPower on Setting Spot Monitor Power on Setting Multiscreen MonitorSequence Timing Setting Secret View Setting Alarm Setup Alarm Port SettingAlarm Auto Reset Setting Alarm Output SettingVideo Loss Alarm Setting Alarm Buzzer SettingVideo Motion Detector Setting Alarm Mode on the Multiscreen Monitor Alarm Mode on the Spot MonitorDisplay Setup Camera Title SetupDisplay Setting Multiscreen Monitor Clock DisplayTitle Display Setting Spot Monitor Alarm Display SettingTitle Display Status DisplayClock and Status Display Position Setting Title Display Position SettingCommunication Setup PS Data SetupUnit Address Setting Baud RateAlarm Data Input Camera Number SetupParity Check Stop BitRS-232C Setup Network Setup System Setup Clock SetupTime Adjustment Setting SET TimePassword Lock Setting Buzzer SettingUser Defined Setting Auto Button Locked SettingDisk Management Disk Space IndicatorDisk Information Error Report System InformationAlarm Recording Backup DVD Drive SetupDVD Format DVD Disk End Setup Emergency Recording BackupDisk Space Display Page Operating Procedures Controlling the Video Input and Monitors Controlling the Spot MonitorSelecting the Spot Monitor Single Spot LiveSelecting the Multiscreen Monitor Controlling the Multiscreen MonitorZooming Single Spot Live Group Single Sequence Live Multiscreen Select Multiscreen Spot LiveAll Input Display with Quad Shift Off Multi Sequence Live All Input Display with Quad Shift On Group DisplayMulti Group setting Quad setting Group Multi SequenceAlarm Input Alarm Control FunctionAlarm Operation Alarm Reset Alarm SuspensionManual Reset Auto ResetInternal Timer Recording Power-on Time Lapse RecordingRecording Manual RecordingAlarm Recording for Manual and Power-on Recording Alarm RecordingSet to ALM-ONLY Set to ALM-MULTI Alarm Recording for Internal Timer ModesTime Lapse Recording Emergency Recording Playback Basic PlaybackStop Forward or Backward searchAlarm jump search Search Record FunctionJump search Record ListDisplay Alarm Log SearchTime & Date Search Single and Multiscreen Spot Playback Display on the MonitorZooming Single Spot Playback Displaying Camera and Playback Image REC PreviewBackup Function JogDialALM-VMD2 Total 931RECORD Data Erase Function Auto Erase FunctionManual Erase Function Button Locked Function To release this function, follow the procedure belowLock Playback of Backup Data Specifications Standard AccessoryGeneral Input and OutputN1102-0 V8QA6084AN