Panasonic WJ-HD500B manual Installing the Optional Network Board

Page 13

■Installing the Optional Network Board

The Network Board WJ-HDB502 is installed exclusively in the WJ-HD500B Disk Recorder.

1.Unplug the power cord from the WJ-HD500B Digital Disk Recorder, or disconnect the plug from the AC out- let.

2.Remove the top cover of the Disk Recorder by remov- ing the 11 screws, as shown in the figure.

Disk Recorder

WJ-HD500B

3.Remove the small plate covering the 10/100BASE-T port hole on the rear of the Disk Recorder by removing the screw shown in the figure.

4.Remove the 6 screws on the board, as shown below, disconnect the CN403, then turn over the Main Board with the front side up.

CN403

Main Board

5.Connect one end of the supplied flat cable to the brown-colored receptacle on the main board, as shown in the figure.

Main Board

Flat Cable (Supplied)

6.Place the main board and CN403 as before, and secure them by tightening the reinstalled screws.

7.Remove a screw on the bracket as shown in the figure, and then fix a supplied grounding wire by tightening the removed screw.

8.Place the Network Board on the brackets, as shown in the figure, then secure it with the grounding wire by tightening the 4 supplied screws.

Network Board

Grounding Wire

Rear Panel

9.Fix the 10/100BASE-T port to the rear panel with the screw removed in step 3.

10.Connect the supplied DC power cable and the other end of the flat cable to the board, as shown in the fig- ure.

DC Power Cable (Supplied)

Flat Cable (Supplied)

10/100BASE-T

Tighten

11.After installing the board, secure the top cover by tight- ening the screws.

14

Image 13

Contents Operating Instructions Lightning flash with arrowhead symbol Contents Preface FeaturesReliable recording of events Easy image searchPrecautions Front View @8Setup/Escape Button SETUP/ESC @4Alarm Search Button Alarm Search1Numeric Buttons 1 2Set Button SET#1Hard Disk Drive Indicator HDD @9Direction Buttons CDA B #0Full Indicator Full$1Multiscreen Output Connector Multiscreen OUT $22Spot Output Connector Spot OUT$9Mode Selector Mode $7Alarm Port Alarm2Gen-lock Output Connector GEN-LOCK OUT 8Power Switch Power ON/OFF1Lock Button Lock WV-CU50 Remote Controller2Monitor Selection Button 3Multiscreen Selection Button1Link Indicator Link 9Alarm Search Button Alarm SearchBlinking Pause mode 0JogDial 6Electronic Zoom Button EL-ZOOMInstalling the Optional Hard Disk InstallationInstalling the Optional Network Board Installing the Optional Motion Detector Board Mounting into the Rack Basic System ConnectionsSystem Expansion Shown below are examples of system connectionsConnection with the Camera Sites Connection with the Remote ControllerConnection with the Monitors Alarm Alarm Port ConnectionControl Port Connection Connection with Control output Connection with the Uninterrupted Power Supply UPSConnection with the Extension Units Switch SettingScsi Connection ModeConnection with the DVD Extension Unit Switch SettingsConnection with the DVD Extension Unit without HDD Copy WJ-HDE510B EXT Connection with the DVD Extension Unit with HDDConnection to PS Data Compatible Equipment Mode Selector Setting10/100BASE-T Port Connection Serial Port ConnectionPage Preparations Power UP Procedure Formatting the Hard Disk 1DISK Format Formatting the DVD-RAM Disk Mirroring Function To deactivate the mirror function Disk Remove Spot and Multiscreen Monitor Monitors and DisplaysStatus Display Time DisplaySystem Status Display Format Error orGroup Display Electronic Zoom DisplayHard Disk Timer RecorderManual Recorder Emergency RecorderMulti Shot Recording Time Lapse RecordingDynamic Recording is set to OFF Dynamic Recording is set to ALM-ONLY One Shot RecordingPage Setup Procedures Displaying the Setup Menu Setup MenuSetup Timer Setting Recording Setup Programming Menu SetupDisplay Setup Communication Setup Timer Setting Recording Quality Setup Recording SetupVideo Pixels Resolution Color Mode SettingGroup Title Setup Group SetupCamera Assignment SpacePlayback Mode Setup Thumbnail Display SetupShuttle Speed Setup Recording of the Title DisplayManual Recording Mode Setting Hard Disk End Setup→ Manual with Audio → Manual Without Audio → Event Recording Manual Recording Program Timer Alarm Active Mode Manual RecordingSpecial Day Timer Time Lapse Recording Internal Timer External Program TimerEvent Recording Alarm Active ModeMulti Shot Recording Internal Timer One Shot Recording Internal Timer Emergency Recording Time Lapse Recording Sequence Setup Multiscreen Monitor Multiplexer SetupLive Sequence Pattern Setting Live SequenceQuad Pattern Setup Quad Shift SettingSequence Timing Setting Group Multi Sequence Setting Sequence Setup Spot MonitorAuto Skip Setting Live Sequence Pattern SettingPower on Setting Spot Monitor Power on Setting Multiscreen MonitorSequence Timing Setting Secret View Setting Alarm Port Setting Alarm SetupAlarm Auto Reset Setting Alarm Output SettingVideo Loss Alarm Setting Alarm Buzzer SettingVideo Motion Detector Setting Alarm Mode on the Spot Monitor Alarm Mode on the Multiscreen MonitorCamera Title Setup Display SetupDisplay Setting Multiscreen Monitor Clock DisplayAlarm Display Setting Title Display Setting Spot MonitorTitle Display Status DisplayTitle Display Position Setting Clock and Status Display Position SettingPS Data Setup Communication SetupUnit Address Setting Baud RateInput Camera Number Setup Alarm DataParity Check Stop BitRS-232C Setup Network Setup Clock Setup System SetupTime Adjustment Setting SET TimeBuzzer Setting Password Lock SettingUser Defined Setting Auto Button Locked SettingDisk Management Disk Space IndicatorDisk Information System Information Error ReportAlarm Recording Backup DVD Drive SetupDVD Format DVD Disk End Setup Emergency Recording BackupDisk Space Display Page Operating Procedures Controlling the Spot Monitor Controlling the Video Input and MonitorsSelecting the Spot Monitor Single Spot LiveSelecting the Multiscreen Monitor Controlling the Multiscreen MonitorZooming Single Spot Live Group Single Sequence Live Multiscreen Select Multiscreen Spot LiveAll Input Display with Quad Shift Off All Input Display with Quad Shift On Group Display Multi Sequence LiveGroup Multi Sequence Multi Group setting Quad settingAlarm Input Alarm Control FunctionAlarm Operation Alarm Suspension Alarm ResetManual Reset Auto ResetPower-on Time Lapse Recording Internal Timer RecordingRecording Manual RecordingAlarm Recording for Manual and Power-on Recording Alarm RecordingSet to ALM-ONLY Set to ALM-MULTI Alarm Recording for Internal Timer ModesTime Lapse Recording Emergency Recording Basic Playback PlaybackStop Forward or Backward searchSearch Record Function Alarm jump searchJump search Record ListDisplay Alarm Log SearchTime & Date Search Single and Multiscreen Spot Playback Display on the MonitorZooming Single Spot Playback REC Preview Displaying Camera and Playback ImageJogDial Backup FunctionALM-VMD2 Total 931RECORD Auto Erase Function Data Erase FunctionManual Erase Function Button Locked Function To release this function, follow the procedure belowLock Playback of Backup Data Standard Accessory SpecificationsGeneral Input and OutputN1102-0 V8QA6084AN