Panasonic TH-65PB2W PC Input Terminals connection, Signal Names for Mini D-sub 15P Connector

Page 12

Connections

 

PC Input Terminals connection

 

Shared with DVI-D IN.

COMPUTER

 

Conversion adapter

 

(if necessary)

(Female)

 

 

Mini D-sub 15p

 

RGB

 

PC cable

 

(Male)

Audio

Stereo mini plug (M3)

 

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•With regard to the typical PC input signals that are described in the applicable input signals list (see page 60), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list.

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

•The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

•Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

•Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”

(when Component signal connection) or “RGB” (when RGB signal connection). (see page 46)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10

9

 

8

7

6

15

14

 

13

12

 

11

Pin No.

Signal Name

Pin No.

Signal Name

Pin No.

Signal Name

1

R (PR/CR)

6

GND (Ground)

11

NC (not connected)

 

 

 

 

 

 

2

G (Y)

7

GND (Ground)

12

SDA

 

 

 

 

 

 

3

B (PB/CB)

8

GND (Ground)

13

HD/SYNC

 

 

 

 

 

 

4

NC (not connected)

9

+5 V DC

14

VD

 

 

 

 

 

 

5

GND (Ground)

10

GND (Ground)

15

SCL

Pin Layout for PC Input Terminal

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operating Instructions Display Operations Table of Contents Important Safety Notice Important InformationTrademark Credits Safety Precautions SetupDo not place any objects on top of the Plasma Display Transport only in upright positionSafety Precautions When using the Plasma DisplayIf problems occur during use Electric shocks can result if this is not done Do not burn or breakup batteriesAccessories Accessories SupplyRemote Control Batteries Connections AC cord connection and fixing, cable fixingSpeaker connection Video equipment connectionConnections Video and Component / RGB in connection DVI-D Input Connector Signal NameHdmi connection DVI-D in connectionSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionCommand Serial Terminals connectionComputer Communication parametersPower On / Off Starting up the networkPower On / Off Selecting the input signal PC Network Whiteboard Video COMPONENT* Hdmi DVIPC Network Whiteboard Slot Input Video Component Hdmi DVI Slot Input Input terminal in Terminal BoardRemote control sensor Input button Input signal selection seeBasic Controls Brightness SensorECO Mode ECO Basic ControlsAll Aspect mode Aspect ControlsDigital Zoom Multi PIP Settings PIP ModeUsing Two Screen Display On-Screen Menu Displays Adjusting Pos./Size Using Remote ControlAuto mode Adjusting Pos./Size Adjust so that any such noise is minimizedClamp Position During Component/PC input signal Optimum value for Clamp Position adjustmentIs adjusted as follows For 2k1k signals 2k1kPicture Adjustments Advanced settings Picture AdjustmentsPicture Profiles MY Picture MEMORY1Saving profiles Picture ProfilesExample Specifying MY Picture Select All deleteLoading profiles Editing profilesDeleting profiles Renaming profilesSound Adjustment SDI Sound OutputSetup menu Network SetupSetup menu screen Day/Time Setup / On/Off Timer Setup Day/Time SetupOn/Off Timer Setup Touch-Pen Settings Slot Input NetworkTouch-Pen Settings Standby pen charging modePairing UnpairingMulti PIP Settings Multi PIPMode selection Start settingScreensaver For preventing image retention Function selectionSetup of Screensaver Time Screensaver For preventing image retentionExtended life settings Picture Mode ContrastReduces screen image retention Image Retention Reduction MenuExpress settings Nanodrift ModeReduces screen image retention Nanodrift SaverCustom settings ResetAdjust Set each menu SelectECO Mode settings ECO ModeCustomizing the Input labels Function Button Settings Input SLOT* Input WhiteboardNo activity power off Menu Display Duration / OSD BrightnessOSD Language Display orientationSetup for Input Signals Component / RGB-in selectYUV / RGB-in select Component RGBSignal menu Setup for Input SignalsSetting RGB sync signal Setting Component sync signalSync SDI ThroughInput signal display Noise reductionAdvanced NR Sets the three NR functions separatelyOptions Adjustments Press for more than 3 seconds. Press to select OptionsOptions Adjustments Input lock SeeStudio Gain Weekly Command Timer NormalisationPress to select a command number Press to select Command NoCommand setting screen Press to select Time / CommandAudio input select Set Touch Panel mode to On Select Adjust Calibration modeWhen the menu is not displayed normal screen Hold down for over 3 secondsInput Search Input SearchPC Network Slot Input Video Component Hdmi DVI Primary Input, Secondary InputTroubleshooting Plasma Display panelList of Aspect Modes 149Applicable Input Signals Mark Applicable input signalApplicable Input Signals Shipping conditionVideo input Video Command list of Weekly Command Timer Specifications TH-50PB2W TH-65PB2WThis product incorporates the following software Customer’s Record
Top Page Image Contents