Panasonic TH-65PB2W, TH-50PB2W Connections, AC cord connection and ﬁxing, cable ﬁxing

Page 8

Connections

AC cord connection and ﬁxing, cable ﬁxing

AC cord ﬁxing

Unplug the AC cord

Plug the AC cord into the display unit.

Plug the AC cord until it clicks.

Note:

Make sure that the AC cord is locked on both the left and right sides.

Unplug the AC cord pressing the two knobs.

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁrst.

When using the Wall-hanging bracket (vertical) (for TH-50PB2W)

Note:

When using the Wall-hanging bracket (vertical)(TY-WK42PV20), use the holes and to secure the cables. If the clamper is used on the hole , the cables may be caught by the wall-hanging bracket.

TH-50PB2W

TH-65PB2W

Using the clamper

Secure any excess cables with clamper as required.

Note:

One clamper is supplied with this unit. In case of securing cables at three positions, please purchase it separately.

	1 Attach the clamper	To remove from the unit:
	hole
		snaps
	Insert the clamper	Keep pushing
	Insert the clamper	both side
	in a hole.	both side
	in a hole.	snaps
		snaps

2 Bundle the cables

To loosen:

	Set the		Keep
hooks	tip in the	knob	pushing
	hooks		the knob

8

Image 8

Contents Operating Instructions Display Operations Table of Contents Trademark Credits Important Safety NoticeImportant Information Safety Precautions SetupDo not place any objects on top of the Plasma Display Transport only in upright positionIf problems occur during use Safety PrecautionsWhen using the Plasma Display Electric shocks can result if this is not done Do not burn or breakup batteriesRemote Control Batteries AccessoriesAccessories Supply Connections AC cord connection and ﬁxing, cable ﬁxingConnections Speaker connectionVideo equipment connection Video and Component / RGB in connection DVI-D Input Connector Signal NameHdmi connection DVI-D in connectionSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionCommand Serial Terminals connectionComputer Communication parametersPower On / Off Starting up the networkPower On / Off Selecting the input signal PC Network Whiteboard Video COMPONENT* Hdmi DVIPC Network Whiteboard Slot Input Video Component Hdmi DVI Slot Input Input terminal in Terminal BoardRemote control sensor Input button Input signal selection seeBasic Controls Brightness SensorECO Mode ECO Basic ControlsAll Aspect mode Aspect ControlsDigital Zoom Using Two Screen Display Multi PIP SettingsPIP Mode On-Screen Menu Displays Auto mode Adjusting Pos./SizeUsing Remote Control Adjusting Pos./Size Adjust so that any such noise is minimizedClamp Position During Component/PC input signal Optimum value for Clamp Position adjustmentIs adjusted as follows For 2k1k signals 2k1kPicture Adjustments Advanced settings Picture AdjustmentsPicture Proﬁles MY Picture MEMORY1Saving proﬁles Picture ProﬁlesExample Specifying MY Picture Select All deleteLoading proﬁles Editing proﬁlesDeleting proﬁles Renaming proﬁlesSound Adjustment SDI Sound OutputSetup menu screen Setup menuNetwork Setup On/Off Timer Setup Day/Time Setup / On/Off Timer SetupDay/Time Setup Touch-Pen Settings Slot Input NetworkTouch-Pen Settings Standby pen charging modePairing UnpairingMulti PIP Settings Multi PIPMode selection Start settingScreensaver For preventing image retention Function selectionSetup of Screensaver Time Screensaver For preventing image retentionExtended life settings Picture Mode ContrastReduces screen image retention Image Retention Reduction MenuExpress settings Nanodrift ModeReduces screen image retention Nanodrift SaverCustom settings ResetAdjust Set each menu SelectECO Mode settings ECO ModeCustomizing the Input labels Function Button Settings Input SLOT* Input WhiteboardNo activity power off Menu Display Duration / OSD BrightnessOSD Language Display orientationSetup for Input Signals Component / RGB-in selectYUV / RGB-in select Component RGBSignal menu Setup for Input SignalsSetting RGB sync signal Setting Component sync signalSync SDI ThroughInput signal display Noise reductionAdvanced NR Sets the three NR functions separatelyOptions Adjustments Press for more than 3 seconds. Press to select OptionsOptions Adjustments Input lock SeeStudio Gain Weekly Command Timer NormalisationPress to select a command number Press to select Command NoCommand setting screen Press to select Time / CommandAudio input select Set Touch Panel mode to On Select Adjust Calibration modeWhen the menu is not displayed normal screen Hold down for over 3 secondsInput Search Input SearchPC Network Slot Input Video Component Hdmi DVI Primary Input, Secondary InputTroubleshooting Plasma Display panelList of Aspect Modes 149Applicable Input Signals Mark Applicable input signalVideo input Video Applicable Input SignalsShipping condition Command list of Weekly Command Timer Speciﬁcations TH-50PB2W TH-65PB2WThis product incorporates the following software Customer’s Record