Panasonic TH-65PB2W, TH-50PB2W Electric shocks can result if this is not done

Page 6

Safety Precautions

CAUTION

When using the Plasma Display

Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.

•Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.

Be sure to disconnect all cables before moving the Plasma Display.

•If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged, and fire or electric shock could result.

Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any cleaning.

• Electric shocks can result if this is not done.

Clean the power cable regularly to prevent it becoming dusty.

•If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in fire. Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.

Do not burn or breakup batteries.

• Batteries must not be exposed to excessive heat such as sunshine, fire or the like.

This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reflected light from your Plasma Display.

Cleaning and maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

•If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

•Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

•If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

•Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

•Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operating Instructions Display Operations Table of Contents Important Safety Notice Important InformationTrademark Credits Do not place any objects on top of the Plasma Display Safety PrecautionsSetup Transport only in upright positionSafety Precautions When using the Plasma DisplayIf problems occur during use Electric shocks can result if this is not done Do not burn or breakup batteriesAccessories Accessories SupplyRemote Control Batteries Connections AC cord connection and fixing, cable fixingSpeaker connection Video equipment connectionConnections Video and Component / RGB in connection Hdmi connection DVI-D Input ConnectorSignal Name DVI-D in connectionSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionComputer CommandSerial Terminals connection Communication parametersPower On / Off Starting up the networkPower On / Off PC Network Whiteboard Slot Input Video Component Hdmi DVI Selecting the input signalPC Network Whiteboard Video COMPONENT* Hdmi DVI Slot Input Input terminal in Terminal BoardBasic Controls Remote control sensorInput button Input signal selection see Brightness SensorECO Mode ECO Basic ControlsAll Aspect mode Aspect ControlsDigital Zoom Multi PIP Settings PIP ModeUsing Two Screen Display On-Screen Menu Displays Adjusting Pos./Size Using Remote ControlAuto mode Adjusting Pos./Size Adjust so that any such noise is minimizedIs adjusted as follows For 2k1k signals Clamp Position During Component/PC input signalOptimum value for Clamp Position adjustment 2k1kPicture Adjustments Advanced settings Picture AdjustmentsPicture Profiles MY Picture MEMORY1Example Specifying MY Picture Saving profilesPicture Profiles Select All deleteDeleting profiles Loading profilesEditing profiles Renaming profilesSound Adjustment SDI Sound OutputSetup menu Network SetupSetup menu screen Day/Time Setup / On/Off Timer Setup Day/Time SetupOn/Off Timer Setup Touch-Pen Settings Slot Input NetworkPairing Touch-Pen SettingsStandby pen charging mode UnpairingMulti PIP Settings Multi PIPScreensaver For preventing image retention Mode selectionStart setting Function selectionSetup of Screensaver Time Screensaver For preventing image retentionReduces screen image retention Extended life settingsPicture Mode Contrast Image Retention Reduction MenuReduces screen image retention Express settingsNanodrift Mode Nanodrift SaverAdjust Custom settingsReset Set each menu SelectECO Mode settings ECO ModeCustomizing the Input labels Function Button Settings Input SLOT* Input WhiteboardOSD Language No activity power offMenu Display Duration / OSD Brightness Display orientationYUV / RGB-in select Setup for Input SignalsComponent / RGB-in select Component RGBSignal menu Setup for Input SignalsSync Setting RGB sync signalSetting Component sync signal SDI ThroughAdvanced NR Input signal displayNoise reduction Sets the three NR functions separatelyOptions Adjustments Press for more than 3 seconds. Press to select OptionsOptions Adjustments Input lock SeeStudio Gain Weekly Command Timer NormalisationCommand setting screen Press to select a command numberPress to select Command No Press to select Time / CommandAudio input select When the menu is not displayed normal screen Set Touch Panel mode to On Select AdjustCalibration mode Hold down for over 3 secondsPC Network Slot Input Video Component Hdmi DVI Input SearchInput Search Primary Input, Secondary InputTroubleshooting Plasma Display panelList of Aspect Modes 149Applicable Input Signals Mark Applicable input signalApplicable Input Signals Shipping conditionVideo input Video Command list of Weekly Command Timer Specifications TH-50PB2W TH-65PB2WThis product incorporates the following software Customer’s Record
Top Page Image Contents