Panasonic TH-65PB2W, TH-50PB2W operating instructions Power On / Off, Starting up the network

Page 14

Power On / Off

Connecting the AC cord plug to the Plasma Display.

Connecting the plug to the Wall Outlet

Notes:

•Main plug types vary between countries. The power plug shown at right may, therefore, not be the type

ﬁtted to your set.
• When disconnecting the AC cord, be absolutely	Power Indicator
sure to disconnect the AC cord plug at the socket	Power Indicator
outlet ﬁrst.
Press the Power switch on the Plasma Display to	Remote Control Sensor
turn the set on: Power-On.

Power Indicator: Green

[Starting up the network]

It takes some time for the network to start up just after the power is turned on.

During that time, “Network Setup” in the “Setup” menu is grayed out and cannot be set.

Press the button on the remote control to turn the Plasma Display off.

Power Indicator: Red (standby)

Press the button on the remote control to turn the Plasma Display on.

Power Indicator: Green

Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode.

Note:

During operation of the power management function, the power indicator turns orange in the power off state.

14

Image 14

Contents Operating Instructions Display Operations Table of Contents Trademark Credits Important Safety NoticeImportant Information Do not place any objects on top of the Plasma Display Safety PrecautionsSetup Transport only in upright positionIf problems occur during use Safety PrecautionsWhen using the Plasma Display Electric shocks can result if this is not done Do not burn or breakup batteriesRemote Control Batteries AccessoriesAccessories Supply Connections AC cord connection and ﬁxing, cable ﬁxingConnections Speaker connectionVideo equipment connection Video and Component / RGB in connection Hdmi connection DVI-D Input ConnectorSignal Name DVI-D in connectionSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionComputer CommandSerial Terminals connection Communication parametersPower On / Off Starting up the networkPower On / Off PC Network Whiteboard Slot Input Video Component Hdmi DVI Selecting the input signalPC Network Whiteboard Video COMPONENT* Hdmi DVI Slot Input Input terminal in Terminal BoardBasic Controls Remote control sensorInput button Input signal selection see Brightness SensorECO Mode ECO Basic ControlsAll Aspect mode Aspect ControlsDigital Zoom Using Two Screen Display Multi PIP SettingsPIP Mode On-Screen Menu Displays Auto mode Adjusting Pos./SizeUsing Remote Control Adjusting Pos./Size Adjust so that any such noise is minimizedIs adjusted as follows For 2k1k signals Clamp Position During Component/PC input signalOptimum value for Clamp Position adjustment 2k1kPicture Adjustments Advanced settings Picture AdjustmentsPicture Proﬁles MY Picture MEMORY1Example Specifying MY Picture Saving proﬁlesPicture Proﬁles Select All deleteDeleting proﬁles Loading proﬁlesEditing proﬁles Renaming proﬁlesSound Adjustment SDI Sound OutputSetup menu screen Setup menuNetwork Setup On/Off Timer Setup Day/Time Setup / On/Off Timer SetupDay/Time Setup Touch-Pen Settings Slot Input NetworkPairing Touch-Pen SettingsStandby pen charging mode UnpairingMulti PIP Settings Multi PIPScreensaver For preventing image retention Mode selectionStart setting Function selectionSetup of Screensaver Time Screensaver For preventing image retentionReduces screen image retention Extended life settingsPicture Mode Contrast Image Retention Reduction MenuReduces screen image retention Express settingsNanodrift Mode Nanodrift SaverAdjust Custom settingsReset Set each menu SelectECO Mode settings ECO ModeCustomizing the Input labels Function Button Settings Input SLOT* Input WhiteboardOSD Language No activity power offMenu Display Duration / OSD Brightness Display orientationYUV / RGB-in select Setup for Input SignalsComponent / RGB-in select Component RGBSignal menu Setup for Input SignalsSync Setting RGB sync signalSetting Component sync signal SDI ThroughAdvanced NR Input signal displayNoise reduction Sets the three NR functions separatelyOptions Adjustments Press for more than 3 seconds. Press to select OptionsOptions Adjustments Input lock SeeStudio Gain Weekly Command Timer NormalisationCommand setting screen Press to select a command numberPress to select Command No Press to select Time / CommandAudio input select When the menu is not displayed normal screen Set Touch Panel mode to On Select AdjustCalibration mode Hold down for over 3 secondsPC Network Slot Input Video Component Hdmi DVI Input SearchInput Search Primary Input, Secondary InputTroubleshooting Plasma Display panelList of Aspect Modes 149Applicable Input Signals Mark Applicable input signalVideo input Video Applicable Input SignalsShipping condition Command list of Weekly Command Timer Speciﬁcations TH-50PB2W TH-65PB2WThis product incorporates the following software Customer’s Record