Panasonic TH-50PB2W Serial Terminals connection, Computer, Communication parameters, Command

Page 13
Signal names for D-sub 9P connector

Connections

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer.

Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to “RS-232C”. (refer to “Operating Instructions, Network Operations”)

COMPUTER

(Male)

9 8 7 6

5 4 3 2 1

RS-232C Straight cable

Pin layout for SERIAL Terminal

(Female)

D-sub 9p

Notes:

•Use the RS-232C straight cable to connect the computer to the Plasma Display.

•The computer shown is for example purposes only.

•Additional equipment and cables shown are not supplied

with this set.

The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal.

The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

Communication parameters

Signal level

RS-232C compliant

Synchronization method

Asynchronous

Baud rate

9600 bps

Parity

None

Character length

8 bits

Stop bit

1 bit

Flow control

None

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX

 

Colon

Parameter(s)

End

Start

3-character

(1 - 5 bytes)

(03h)

(02h)

command (3 bytes)

 

 

Notes:

•If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command.

•If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.

•S1A and S1B of Command IMS are available only when a dual input terminal board is attached.

•Consult your local Panasonic dealer for detail instructions on command usage.

Pin No.

Details

 

2

R X D

 

3

T X D

 

5

GND

4

• 6

Non use

 

7

(Shorted in this set)

 

8

 

 

1

• 9

NC

These signal names are those of computer specifications.

Command

Command

Parameter

Control details

PON

None

Power ON

POF

None

Power OFF

AVL

**

Volume 00 - 63

AMT

0

Audio MUTE OFF

1

Audio MUTE ON

 

IMS

None

Input select (toggle)

 

SL1

SLOT input (SLOT INPUT)

 

S1A

SLOT input (SLOT INPUT A)

 

S1B

SLOT input (SLOT INPUT B)

 

VD1

VIDEO input (VIDEO)

 

YP1

COMPONENT/RGB IN input

 

 

(COMPONENT)

 

HM1

HDMI input (HDMI)

 

DV1

DVI-D IN input (DVI)

 

PC1

PC IN input (PC)

 

NW1

Network input (NETWORK)

 

WB1

WhiteBoard input (WHITEBOARD)

DAM

None

Screen mode select (toggle)

 

ZOOM

Zoom, Zoom1

 

FULL

16:9

 

JUST

Just, Just1 (For Video/SD/HD signal)

 

NORM

4:3, 4:3 (1)

 

ZOM2

Zoom2 (For Video/SD/HD signal)

 

ZOM3

Zoom3 (For Video/SD/HD signal)

 

SJST

Just2 (For HD signal)

 

SNOM

4:3 (2) (For HD signal)

 

SFUL

4:3 Full (For HD signal)

 

14:9

14:9 (For Video/SD/HD signal)

With the power off, this display responds to PON command only.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operating Instructions Display Operations Table of Contents Important Information Important Safety NoticeTrademark Credits Setup Safety PrecautionsDo not place any objects on top of the Plasma Display Transport only in upright positionWhen using the Plasma Display Safety PrecautionsIf problems occur during use Do not burn or breakup batteries Electric shocks can result if this is not doneAccessories Supply AccessoriesRemote Control Batteries AC cord connection and fixing, cable fixing ConnectionsVideo equipment connection Speaker connectionConnections Video and Component / RGB in connection Signal Name DVI-D Input ConnectorHdmi connection DVI-D in connectionPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorSerial Terminals connection CommandComputer Communication parametersStarting up the network Power On / OffPower On / Off PC Network Whiteboard Video COMPONENT* Hdmi DVI Selecting the input signalPC Network Whiteboard Slot Input Video Component Hdmi DVI Slot Input Input terminal in Terminal BoardInput button Input signal selection see Remote control sensorBasic Controls Brightness SensorBasic Controls ECO Mode ECOAspect Controls All Aspect modeDigital Zoom PIP Mode Multi PIP SettingsUsing Two Screen Display On-Screen Menu Displays Using Remote Control Adjusting Pos./SizeAuto mode Adjust so that any such noise is minimized Adjusting Pos./SizeOptimum value for Clamp Position adjustment Clamp Position During Component/PC input signalIs adjusted as follows For 2k1k signals 2k1kPicture Adjustments Picture Adjustments Advanced settingsMY Picture MEMORY1 Picture ProfilesPicture Profiles Saving profilesExample Specifying MY Picture Select All deleteEditing profiles Loading profilesDeleting profiles Renaming profilesSDI Sound Output Sound AdjustmentNetwork Setup Setup menuSetup menu screen Day/Time Setup Day/Time Setup / On/Off Timer SetupOn/Off Timer Setup Slot Input Network Touch-Pen SettingsStandby pen charging mode Touch-Pen SettingsPairing UnpairingMulti PIP Multi PIP SettingsStart setting Mode selectionScreensaver For preventing image retention Function selectionScreensaver For preventing image retention Setup of Screensaver TimePicture Mode Contrast Extended life settingsReduces screen image retention Image Retention Reduction MenuNanodrift Mode Express settingsReduces screen image retention Nanodrift SaverReset Custom settingsAdjust Set each menu SelectECO Mode ECO Mode settingsCustomizing the Input labels Input SLOT* Input Whiteboard Function Button SettingsMenu Display Duration / OSD Brightness No activity power offOSD Language Display orientationComponent / RGB-in select Setup for Input SignalsYUV / RGB-in select Component RGBSetup for Input Signals Signal menuSetting Component sync signal Setting RGB sync signalSync SDI ThroughNoise reduction Input signal displayAdvanced NR Sets the three NR functions separatelyPress for more than 3 seconds. Press to select Options Options AdjustmentsInput lock See Options AdjustmentsStudio Gain Normalisation Weekly Command TimerPress to select Command No Press to select a command numberCommand setting screen Press to select Time / CommandAudio input select Calibration mode Set Touch Panel mode to On Select AdjustWhen the menu is not displayed normal screen Hold down for over 3 secondsInput Search Input SearchPC Network Slot Input Video Component Hdmi DVI Primary Input, Secondary InputPlasma Display panel Troubleshooting149 List of Aspect ModesMark Applicable input signal Applicable Input SignalsShipping condition Applicable Input SignalsVideo input Video Command list of Weekly Command Timer TH-50PB2W TH-65PB2W SpecificationsCustomer’s Record This product incorporates the following software
Top Page Image Contents